ملخص المحتوى في الصفحة رقم 1
Model PRO 9232a
OWNER’S MANUAL
KEYLESS ENTRY ALARM UPGRADE MODULE
Congratulations on your purchase of the PRO 9232a automotive Keyless Entry
Upgrade Alarm System. This system is a state - of - the - art auto security system
that is designed to automatically arm and disarm when it receives a command from
your existing Factory Keyless Entry Transmitter. Taking a few moments to read this
manual will help to ensure that your vehicle is protected at all times.
NOTE:
The system has the ability to beep
ملخص المحتوى في الصفحة رقم 2
is automatically ( passively ) arming. As an added convenience, the 30 second automatic passive arming will not begin until all doors are closed, allowing passen- gers to exit the vehicle at their convenience. 3. In 30 seconds, you will hear a single short chip from the siren, and the vehicle’s parking lamps will flash one time, indicating that the system has ARMED. At this time, the red dash mounted LED will begin to flash slowly, providing a visual indication that the system is fully armed. 4
ملخص المحتوى في الصفحة رقم 3
installed, the vehicle’s interior lights will turn on for 30 seconds, or until the ignition key is turned on. NOTE: If your system has been programmed for “ passive arming “, then it will begin to re-arm immediately after disarming. This is indicated by a rapid flashing of the red dash mounted LED Opening one of the vehicle’s doors will suspend the passive arming process until all doors have been closed, or until the ignition key has been turned on. INTRUSION WARNING SIGNALS : The system will
ملخص المحتوى في الصفحة رقم 4
TO ENTER THE VALET MODE: 1. Disarm the unit by use of the factory transmitter or by use of the manual override sequence. 2. Turn the ignition switch to the “On” position. 3. Press and hold the valet/override pushbutton switch for 5 seconds. The LED turns on, indicating valet mode has been successfully entered. TO EXIT VALET: With the ignition switch in the on position, press and release the valet/override pushbutton switch one time. The LED turns off indicating the valet mode has successfully
ملخص المحتوى في الصفحة رقم 5
the manual override sequence. If the code is not successfully entered within the three attempts, disarming with the manual override switch will be locked for 10 minutes. In many cases, to increase the security of your system, you may elect to change the manual override code to a number that is more familiar to you, or simply to have a different code than was pre-assigned from the factory. To Change the pre- assigned override code follow the steps outlined below. It is advised you read both sec
ملخص المحتوى في الصفحة رقم 6
Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3. Within 10 seconds, press and release the valet/override switch, 3 times. 4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. Within 10 s
ملخص المحتوى في الصفحة رقم 7
To operate the optional accessory; 1. Press the lock, then unlock, then lock buttons on your keychain transmitter within 3 seconds. 2. The optional accessory will immediately activate. OPTIONAL AUTO LOCK/UNLOCK FEATURE : If your existing factory installed keyless entry system did not include the automatic door lock and unlock feature, then this feature can be activated from the PRO 9232 upgrade module. When this accessory has been added, any time the ignition key is turned to the on position an
ملخص المحتوى في الصفحة رقم 8
PRO 9232a SYSTEM FUNCTIONS AT A GLANCE DASH L.E.D. INDICATORS RAPID FLASHING .......................................................... PASSIVE ARMING SLOW FLASHING ........................................................................... ARMED OFF ........................................................................................... DISARMED ON - SOLID ............................................................................ VALET MODE 3 FLASH ... PAUSE .....................