ملخص المحتوى في الصفحة رقم 1
Assembly Guide
Ab-X100
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Ab-X100 Assembly Guide Obtaining Service Important Safety Instructions For information about product operation or service, When using exercise equipment, basic precautions refer to the Precor web site at www.precor.com where should always be taken, including the following: you can also find customer support numbers or a list of • Read all instructions before assembling the Precor authorized service centers. Ab-X100. These instructions are written for your If you call or e-mail Customer Support,
ملخص المحتوى في الصفحة رقم 4
Ab-X100 Assembly Guide Table of Contents Important Safety Instructions .................................................................................. 3 Obtaining Service ..................................................................................................................................... 3 Preparations .............................................................................................................. 5 Unpacking the Equipment.........................................
ملخص المحتوى في الصفحة رقم 5
Ab-X100 Assembly Guide Required Tools Tools that you need to obtain before assembling the unit include: ❏ Measuring tape ❏ Rubber mallet 1 Preparations ❏ Wire tie cutter or utility knife The Ab-X100 parts are inspected before shipment. Each unit contains several pieces that require Installation Requirements assembly. You may find it helpful to ask for assistance Follow these installation requirements when during the assembly process. assembling the unit: � Review the Important Safety Instruction
ملخص المحتوى في الصفحة رقم 6
Ab-X100 Assembly Guide Hardware Kit Fastener Qty Fastener Qty 1-inch Buttonhead screw (A) 6 ⁵⁄₁₆-inch Washer (H) 4 ³⁄₈-inch Split washer (B) 6 ¾-inch Shoulder bolt (J) 2 ³⁄₈-inch Washer (C) 6 ¾-inch Buttonhead screw (D) 8 Pivot arm cap (K) 2 ⁵⁄₁₆-inch Split washer (E) 14 ⁵⁄₁₆-inch Washer (F) 4 1¼-inch Buttonhead screw (G) 10 Preparations, continued page 6
ملخص المحتوى في الصفحة رقم 7
Ab-X100 Assembly Guide 2 – Plastic foot (L) 2 – End cap (M) Preparations, continued page 7
ملخص المحتوى في الصفحة رقم 8
Ab-X100 Assembly Guide Footrest Assembly 2 Instructions Assembly of the Ab-X100 takes about 45 minutes to complete. If this is the first time you have assembled this type of equipment, plan on allowing more time. Be careful to open boxes and assemble components in the sequence presented in this manual. Handlebars Note: With so many assembled parts, proper alignment and adjustment is critical. While tightening the fasteners, Seat Pad be sure to leave room for adjustments. Do not fully tighten fas
ملخص المحتوى في الصفحة رقم 9
Ab-X100 Assembly Guide Assemble the Main Structure End Cap 1. Insert the End Caps (M) into the Front Support and 2 - 1¼" buttonhead screws attach two plastic feet (L) to its base. Secure the 2 - split washers pieces using two 1¼-inch buttonhead screws (G) two split washers (E) Wrench tighten. Front Support 2. Set the Main Frame in an upright position. Main Frame 3. Cut the wire tie holding the Support Bar to the wheeled Base Support and remove any packing material. 4. Attach the Base Support to
ملخص المحتوى في الصفحة رقم 10
Ab-X100 Assembly Guide 6. Lift the Support Bar so you can access the Pivot Arm mounting holes. 7. Have your assistant angle the Handlebar Main Frame Assembly beneath the Support Bar and position the Pivot Arms so you can insert a shoulder bolt Handlebars through each sleeve. Thread the shoulder bolts (H) into the mounting holes to secure the Pivot Arms. Wrench tighten. 2 - 1" shoulder Note: The Pivot Arms can fall off the Handlebar bolts Assembly, so keep the assembly as level as possible. 2 - p
ملخص المحتوى في الصفحة رقم 11
Ab-X100 Assembly Guide 11. Install the Back Pad Channel Support onto the Linkage Block using Linkage four ¾-inch buttonhead screws (D) Block four split washers (E) Support Bar Wrench tighten. 4 - ¾" buttonhead screws 12. Lift and pull back on the Support Bar so you can 4 - split washers align the Back Pad Channel Support with the Pivot Tube side mounts. Secure the Back Pad Channel Support to the Pivot Tube using four ¾-inch buttonhead screws (D) 4 - ¾" buttonhead screws four split washers (E) 4
ملخص المحتوى في الصفحة رقم 12
Ab-X100 Assembly Guide Attach the Seat and Back Pad 1. Attach the Seat Pad to the Main Frame using four 1¼-inch buttonhead screws (G) four split washers (E) 4 - 1¼" buttonhead screws four flat washers (F) 4 - split washers 4 - flat washers Wrench tighten. 2. Attach the Back Pad to the Back Pad Channel Back Pad Support using four 1¼-inch buttonhead screws (G) four split washers (E) four flat washers (H) Seat Pad Wrench tighten. Back Pad Channel Support This completes the assembly of the Ab-X100.
ملخص المحتوى في الصفحة رقم 13
Ab-X100 Assembly Guide Clean the Pads and Assembly To clean the seat or back pads moisten a clean, soft cloth in a mild solution of soap and water and wipe the pads thoroughly. Dry the pads with a clean, dry cloth. Use the same procedure to clean the Main Frame and plastic parts. Frequently, vacuum the floor underneath the Ab-X100 to prevent the accumulation of dust and dirt. If necessary, use the Footrest to lift the front end and tip the Ab-X100 onto its wheels to roll it to a different locati
ملخص المحتوى في الصفحة رقم 14
Limited Warranty Precor, Incorporated (PRECOR) will repair or replace any of the following components which An individual purchasing PRECOR equipment in California for personal, family or household are defective as to materials or workmanship for products manufactured and sold after June 1, purposes has the right to have defective equipment serviced or repaired during the warranty 1990: period. The warranty period will be extended for the number of whole days that the equipment is out of the buy
ملخص المحتوى في الصفحة رقم 15
ملخص المحتوى في الصفحة رقم 16
Ab-X100 Specifications Length: 57 inches (145 cm) Height: 38 inches (96 cm) Width: 32 inches (81.5 cm) Shipping weight: 186 lb (84 kg) Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 1-800-347-4404 Precor, Icarian, and Move Beyond are registered trademarks of Precor Incorporated. Copyright 2006 Precor Incorporated. Specifications subject to change without notice. www.precor.com NOTICE: Precor is widely recognized for its innovative, award winning designs of
