ملخص المحتوى في الصفحة رقم 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY
Safety Notice
DELUXE SMITH MACHINE
Hardware Identifier
SM-6200
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
SM-6200
Retain This
Manual for
Reference
08-06-09
OWNER'S
MANUAL
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitn
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS BEFORE YOU BEGIN..................................................................................... 1 IMPORTANT SAFETY NOTICES.................................................................... 2 SMITH MACHINE HARDWARE PACK….......…............................................. 4 SMITH MACHINE ASSEMBLY INSTRUCTIONS............................................ 7 EXPLODED DIAGRAM…………………………………………………………….. 19 SMITH MACHINE PARTS LIST………..…………………………………………. 20 MULTI
ملخص المحتوى في الصفحة رقم 3
PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine.
ملخص المحتوى في الصفحة رقم 4
The warning labels shown here have been placed on the Cross Brace, Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3 SMITH MACHINE HARDWARE PACK
ملخص المحتوى في الصفحة رقم 5
4
ملخص المحتوى في الصفحة رقم 6
SMITH MACHINE HARDWARE PACK 5
ملخص المحتوى في الصفحة رقم 7
SMITH MACHINE HARDWARE PACK 6
ملخص المحتوى في الصفحة رقم 8
SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten all nuts and bolts until instructed to do so. B.) Attach one Base Frame (#1) to the Left Vertical Frame (#3). Attach the Cross Brace (#6) to the back of the Left Vertical Frame. Align the holes and secure the Bas
ملخص المحتوى في الصفحة رقم 9
DIAGRAM 1 8
ملخص المحتوى في الصفحة رقم 10
STEP 2 (See Diagram 2) A.) Attach the Vertical Frame Base (#9) to the Cross Brace (#6) from the bottom. Attach the Rear Vertical Frame (#8) onto the Cross Brace on the top. Align the holes and secure them together with two M10 x 2 3/8” Carriage Bolts (#83), Ø ¾” Washers (#89), and M10 Aircraft Nuts (#90). B.) Attach the Backrest Board (#45) to the Rear Vertical Frame (#8). Secure it with two M8 x 2 3/8” Allen Bolts (#75) and Ø 5/8” Washes (#88). 9
ملخص المحتوى في الصفحة رقم 11
STEP 3 (See Diagram 3) A.) Attach the Weight Glide Post (#11) to the bracket on the Vertical Frame Base (#9). Secure it with one 3 1/8” x 1 ¾” Bracket (#31), M10 x 2 ½” Carriage Bolt (#84), Ø ¾” Washer (#89), and M10 Aircraft Nut (#90) to the upper hole, one M10 x 2 ½” Allen Bolt (#81) and one Ø ¾” Washer (#89) to the lower hole. B.) Slide the Sliding Weight Post (#19) onto the Weight Glide Post (#11)) from the top. Make sure the triangular cable connecting bracket on the Sliding
ملخص المحتوى في الصفحة رقم 12
DAIGRAM 3 11
ملخص المحتوى في الصفحة رقم 13
STEP 4 (See Diagram 4) A.) Attach the Butterfly Base (#37) to the Rear Vertical Frame (#8). Secure it with two M10 x 2 ½” Carriage Bolts (#84), Ø ¾” Washers (#89), and M10 Aircraft Nuts (#90). B.) Attach two Swivel Pulley Brackets (#35) to the open brackets on the Rear Vertical Frame (#8). Secure each Bracket with one M10 x 2 ½” Allen Bolt (#81), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#90). Do not over tighten the nuts and bolts. Make sure the brackets are able to swivel on
ملخص المحتوى في الصفحة رقم 14
CABLE LOOP DIAGRAM 13
ملخص المحتوى في الصفحة رقم 15
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 142” Upper Cable (#40) to the front opening on the Upper Frame (#7). Attach a Pulley (#59) to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#79), two Ø 1 1/8” x 3/8” Pulley Bushings (#52), and one M10 Aircraft Nut (#90). Make sure the ball stopper on the Cable is underneath the Frame. B.) Draw the Cable over the Pulley along the Upper Frame to the opening in between the two Cover Brackets (#10). Attach a Pulley to the
ملخص المحتوى في الصفحة رقم 16
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 86” Butterfly Cable (#42) to the clip on the Right Butterfly (#39). Draw the Cable to the right open Swivel Pulley Bracket (#35). B.) Attach a Small Pulley (#58) to the Swivel Pulley Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#78), two Ø ¾” Washers (#89), and one M10 Aircraft Nut (#90). C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley Bracket (#36). Install a Pull
ملخص المحتوى في الصفحة رقم 17
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Insert the tip of the 127” Lower Cable (#41) through the opening on the Foot Plate (#26) to the opening on the Vertical Frame Base (#9). B.) Attach a Small Pulley (#58) to the opening. Attach the Foot Plate to the Frame. Align the holes and secure the Foot Plate, Vertical Frame Base, and the Small Pulley with one M10 x 2 ¾” Allen Bolt (#93), two Ø 1” x ¾” Pulley Bushings (#53), and one M10 Aircraft Nut (#90). Secure the Foot Plate to the
ملخص المحتوى في الصفحة رقم 18
DIAGRAM 7 17
ملخص المحتوى في الصفحة رقم 19
STEP 8 (See Diagram 8) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#13) in between the two Safety Stop Frames (#16). Align the holes and insert the Weight Bar (#15) all the way through. Center the bar and use the two M8 x 3/8” Allen Bolts (#86) on the two Safety Stop Frame to secure the Weight Bar on each side. B.) Turn the safety catch hook forward on the Lifting Sleeve to secure its position on the selected holes on the Front Verti
ملخص المحتوى في الصفحة رقم 20
SMITH CAGE EXPLODED DIAGRAM 19
