ملخص المحتوى في الصفحة رقم 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
®
MARCY MWM-1840
Hardware Pack
HOME GYM
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-1840
Retain This
Manual for
Reference
®
IMPEX INC.
101015
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
www.impex-fitness.com
MANUAL
info@impe
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 PARTS LIST…………………………………………………………………………………. 26 RESISTA
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a tim
ملخص المحتوى في الصفحة رقم 4
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Middle Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
ملخص المحتوى في الصفحة رقم 5
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
ملخص المحتوى في الصفحة رقم 6
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
ملخص المحتوى في الصفحة رقم 7
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6
ملخص المحتوى في الصفحة رقم 8
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Middle Stabilizer (#2) on flat surface. B.) Attach the Base Frame (#3) to the front of Middle Stabilizer. Attach the Rear Stabilizer (#20) to the Middle Stabilizer from rear. C.) Align the holes. Secure them together with two
ملخص المحتوى في الصفحة رقم 9
STEP 2 (See Diagram 2) A.) Insert the two Guide Rods (#11) into the holes on the Middle Stabilizer (#2). Secure each Guide Rod with one M10 x 1” Allen Bolt (#81) and two ¾” Washers (#91) from the bottom. Slide two Ø 2 ¼” x 1” Guide Rod Rubber Bumpers (#39) onto the two Guide Rods from top to bottom. B.) Do not tighten all Nuts and Bolts starting from this procedure until instructed to do so. C.) Attach the Power Station Vertical Frame (#26) to the Rear Stabilizer (#20). Secure th
ملخص المحتوى في الصفحة رقم 10
DIAGRAM 2 9
ملخص المحتوى في الصفحة رقم 11
STEP 3 (See Diagram 3) A.) Slide 14 Weight Plates (#42) onto the Guide Rods (#11). Make sure the deep grooves on the Weight Plates all face the back of the machine and downward. B.) Align the holes on the Weight Plates. Insert a Selector Rod (#21) through the center hole. Slide the Selector Stem (#41) onto the Guide Rods. C.) Use the Weight Selector Pin (#64) to select the number of Weight Plates to exercise. Attach the ring on Weight Selector Pin’s cable onto the Selector Rod. D.) No
ملخص المحتوى في الصفحة رقم 12
STEP 4 (See Diagram 4) A.) Place the Upper Frame (#1) onto the Vertical Frame (#4). B.) Attach the brackets on the Upper Frame to the two Guide Rods. Secure the Guide Rods to the brackets with two M10 x 1” Allen Bolts (#81) and Ø ¾” Washers (#91). C.) Secure the Upper Frame to the Power Station Vertical Frame (#26) with two M10 x 2 3/8” Carriage Bolts (#72), one 4 ¾” x 3 ½” Bracket (#18), two Ø ¾” Washers (#91), and two M10 Aircraft Nuts (#97). D.) Secure the Upper Frame to the Ver
ملخص المحتوى في الصفحة رقم 13
DIAGRAM 4 12
ملخص المحتوى في الصفحة رقم 14
STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#8) to the Upper Frame (#1). Secure it with one 8 ½” Front Press Axle (#19), two Ø 1” Large Washers (#96), and two M10 Aircraft Nuts (#97). Do not over tighten the Nuts. B.) Insert the axle on the Left Butterfly (#9) through the open hole on Front Press Base from bottom. Secure it with one Ø 1” Large Washer (#96) and one M10 Aircraft Nuts (#97). Do not over tighten the Nut. Push one Large Foam Roll (#37) onto the Left Butterfly.
ملخص المحتوى في الصفحة رقم 15
DIAGRAM 5 14
ملخص المحتوى في الصفحة رقم 16
STEP 6 (See Diagram 6) A.) Attach the Left Dip Support (#28) into Right Dip Support (#27) behind the Power Station Vertical Frame (#26). B.) Attach the holes on the bracket of Left & Right Dip Support to the hole on the Vertical Frame. Align the holes. Secure the Left & Right Dip Support, and the Vertical Frame together with one M10 x 4 7/8” Hex Bolt (#86), one Ø 1” Washers (#92), one Ø ¾” Washer (#91), and one M10 Aircraft Nut (#97). Do not over tighten the Nuts and Bolts. Make sure th
ملخص المحتوى في الصفحة رقم 17
DIAGRAM 6 16
ملخص المحتوى في الصفحة رقم 18
STEP 7 (See Diagram 7) A.) Attach one Swivel Pulley Bracket (#17) to the open bracket on the back of Vertical Frame (#4). Secure it with one M10 x 2 ½” Allen Bolt (#76), two Ø ¾” Washers (#91), and one M10 Aircraft Nut (#97). Do not over tighten the Nut and Bolt. Make sure the Swivel Pulley Bracket can swivel freely. B.) Repeat Procedure A to install the other Swivel Pulley Bracket on the other side. C.) Attach a Front Press Handle (#12) to the Left & Right Butterfly (#9 & #10). Secure eac
ملخص المحتوى في الصفحة رقم 19
STEP 8 (See Diagram 8) A.) Attach the Power Station Arm Pads (#35) to the Right & Left Dip Support (#27 & #28). Secure each Arm Pad with two M8 x 2 ¾” Allen Bolts (#84) and two Ø 5/8” x 1” Curved Washers (#94). B.) Attach two Vertical Handles (#13) to Right & Left Dip Support. Secure each Handle to each Support with one M10 x 1” Allen Bolt (#81) and Ø ¾” x 1 1/8” Curved Washer (#95). C.) Insert 15 ¾” Long Foam Tube halfway through the hole on Seat Support (#5). Insert 15” Short Foam Tube
ملخص المحتوى في الصفحة رقم 20
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 127 ½” Upper Cable (#56) to the front open bracket under the Upper Frame (#1). B.) Attach a Pulley (#40) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#74), two Ø ¾” Washers (#91), and one M10 Aircraft Nut (#97). C.) Draw the Cable under the Upper Frame towards the back of the machine to the open bracket on Vertical Frame (#4). Repeat B to install a Pulley. D.) Draw the Cable around the Pulley then pull back to th
