ملخص المحتوى في الصفحة رقم 1
Customer Service
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A Huffy Company
WRITE IN YOUR MODEL NUMBER:___________
Portable Basketball System
Owners Manual
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN
SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe
operation of the system.
To ensure safety, do not attempt to assemble this system without following the
instructions carefu
ملخص المحتوى في الصفحة رقم 2
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. 30 • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net
ملخص المحتوى في الصفحة رقم 3
IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL Remove all parts from packing material and separate tanks from the shipping position. 1. Carefully, position front tank (1) upside down. Secure wheel (2) into place from bottom side (illust. A) 2. making sure the wheel bracket (5) seeds into base as in illust. B. Repeat procedure for opposite wheel. Finger tighten, then upright assembly. 1 5 A B 3 2 3 4 SIDE VIEW 6 5 6 4 BOTTOM VIEW BOTTOM VIEW 7 TOP Correctly id
ملخص المحتوى في الصفحة رقم 4
6. Spread collar (10) open and carefully raise collar (10) to 35-1/2” (90.2 cm) taped mark. Finger tighten hardware to prevent collar (10) Install rod (15) through holes in bottom pole 7. from moving and scratching pole. section (9) and eyebolt (16). NOTE: Avoid scratching pole. 10 9 15 10 13 7 11 12 8 9 12 14 16 9 8. Set rear tank (17) onto front tank (1) and insert pole assembly into tank assembly as shown. 16 1 17 4 P/N 211657B 04/03
ملخص المحتوى في الصفحة رقم 5
9. Carefully position system on its side, and secure IMPORTANT! bottom of pole to tank as shown, a deep socket DO NOT 1 is recommended. Upright system. OVER TIGHTEN. NOTE: Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this step. 18 9 12 18 12 19 19 17 BOTTOM VIEW 10. Loosen hardware on collar (10) and FRONT secure struts (20) to collar (10) as shown VIEW and tighten. NOTE: Final adjustments to collar may need to be made. Refer to
ملخص المحتوى في الصفحة رقم 6
11. Once again, carefully position system in the side position and secure strut (20) to tank (1) as shown. Repeat for opposite side. Completely tighten including bolts from step 2 then carefully upright system. 12 11 13 20 1 6 P/N 211657B 04/03
ملخص المحتوى في الصفحة رقم 7
ELEVATOR INSTALLATION 13. Install left screw jack support plate (26) and right screw jack support plate (27) to pole. Finger tighten. 4 6 26 4 24 6 24 4 4 27 WARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING (See Text Page) Note (See Text Page) SAWHORSE OR SUPPORT TABLE MTT01.EPS 7 04/03 P/N 211657B
ملخص المحتوى في الصفحة رقم 8
1 9 8 7 Attach height decal (28) on screw jack (29). Align lower edge 14. of decal with bottom of black indicator tube. 31 32 WARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY 29 INJURY AND/OR PROPERTY DAMAGE. 28 Center screw jack (29) between support plates (26 & 27) 15. and secure as shown below. Finger tighten. Place cover over screw jack (29). Install pole cap (32). 16. 4 4 4 4 33 33 6 6 27 26 FRONT VIEW OF ASSEMBLY 29
ملخص المحتوى في الصفحة رقم 9
17. 36 19 36 19 35 NOTE: Be sure to use proper bracket as shown. 35 37 9 04/03 P/N 211657B
ملخص المحتوى في الصفحة رقم 10
18. Finger tighten. 4 37 6 39 39 4 40 38 38 Refer To Instructions Included With Rim Hardware For Rim Assembly. 10 P/N 211657B 04/03
ملخص المحتوى في الصفحة رقم 11
20. Finger tighten. 6 4 39 37 39 38 40 4 38 11 04/03 P/N 211657B
ملخص المحتوى في الصفحة رقم 12
Secure board and elevator tube assembly to pole assembly as shown. Finger tighten. 21. IMPORTANT! 25 DO NOT OVER 4 TIGHTEN. WARNING 40 4 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN 6 SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. 38 38 SAWHORSE OR SUPPORT TABLE Insert spacer (41) through top holes of height indicator cover (31) and screw jack assembly 4 22. as shown. Align spacer and 41 40 screw jack assembly between elevator tubes (34) and
ملخص المحتوى في الصفحة رقم 13
23. WARNING DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY, IT MAY TIP OVER. 1 Roll assembly to desired playing area. Secure assembly to ground using rope (21) and tie down stake (22). Fill larger 23 tank (1) with water (approx. 24 gallons (91 liters)) or sand (approx. 300 lbs (136 kg)) and smaller tank (17) with (approx. 10 gallons (78.9 liters)) or sand (approx. 120 21 lbs (54.4 kg)) and snap fill caps (23) in place. 23 IMPORTANT! Two Gallons (7.6 Liter) of Non-Toxic Antifreeze 17 23 Required.
ملخص المحتوى في الصفحة رقم 14
Apply height 25. adjustment label (30) to front of pole as shown. 30 10 feet (3.05 m) Regulation Rim Height is 10 feet (3.05 m). Height Adjustment Position looped end of height adjustment crank 26. (34) onto hook as shown. Rotate crank handle to raise or lower backboard. View label (28) to determine approximate backboard height. NOTE: If height adjustment is difficult to operate, you may have over tightened the areas indicated. 28 WARNING STORE CRANK OUT OF REACH OF CHILDREN. DO NOT ALLOW
ملخص المحتوى في الصفحة رقم 15
PARTS LIST Item Qty. Part No. Description Item Qty. Part No. Description 21 1 202438 Black Nylon Rope 1 1 226350 Tank, (Front Section) 22 1 203124 Stake, Tie Down 2 2 226403 Wheel 23 3 206219 Fill Cap 3 2 206245 Bolt, Hex Head, 1/2-13 x 5-1/2 Long 24 2 206273 Bolt, Hex Head, 1/2-13 x 4-1/2 Long 4 24 203474 Washer, 1/2 I.D., 1-5/64 O.D. 25 4 201651 Spacer 5 2 206341 Bracket, Wheel 26 1 906277 Plate, Jack Support, (Left) 6 13 206340 Locknut, Hex, 1/2-13 27 1 906276 Plate, Jack Support, (Right) 7 1
ملخص المحتوى في الصفحة رقم 16
HARDWARE IDENTIFIER Item #40 (5) Item #19 (3) Item #18 (1) Item #24 (2) Item #33 (2) Item #25 (4) Item #35 (2) Item #36 (2) Item #39 (4) Item #41 (1) * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. HARDWARE IDENTIFIER (CONTINUED) 16 P/N 211657B 04/03
