Huffy RC1200 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Customer Service
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A DIVISION OF RUSSELL CORPORATION
Model 890481
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
This unit is intended for display purposes only and
should not be used for play.
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts

ملخص المحتوى في الصفحة رقم 2

PARTS LIST - See Hardware Identifier Item Qty. Part No. Description 1 1 20176001 P.O.P. Sign 2 12 200892 Plastic Push Clips 3 20 201763 Bolt, Carriage, 3/8-16 x 6.5 Long 4 20 203232 Washer, Flat 3/8 5 20 202460 Saddle Clamp 6 20 203063 Lock Nut, 3/8-16 7 5 901097 Extension Arm, 3.5” Diameter 8 5 900897 3.5” Pole Section 9 10 201611 Bolt, Hex Flange, 5/16-18 x 3 Long 10 20 203218 Washer, Flat, 5/16 11 10 203100 Nut, Hex Flange 5/16-18 12 5 207103 Pole Cap for 3.5” Pole Section 13 5 200NET Spider

ملخص المحتوى في الصفحة رقم 3

1. 2 1 P.O.P. Portable Basketball System FRONT Install pegboard panels onto 2. corresponding side support railings. Attach P.O.P. sign (1) to lower peg board with plastic push clips (2) so that it faces aisle as shown. 01/05 P/N 21165502 3

ملخص المحتوى في الصفحة رقم 4

Install enclosed pole mounting hardware and pole 3. WARNING for each assembly. TWO PEOPLE ARE NECESSARY TO MOUNT THE ELEVATOR ASSEMBLY TO THE POLE. ONE PERSON SHOULD NOT ATTEMPT TO DO THIS ALONE. 3-1/2” Rnd. Pole X 30” Pole 3 Upper Support Railing 8 5 4 3-1/2” Rnd. Pole TOP 3-1/2” Rnd. Pole 6 VIEW NOTE: Enclosed Are Two Sets Of Brackets + Hardware For BACK (Each) Pole Installation P/N 21165502 01/05 4

ملخص المحتوى في الصفحة رقم 5

Pole Locations Refer To Combo For Goal Assembly Instructions Mount extension arm (7) and 1. rim to backboard using appropriate instruction sheet. NOTE: For spring loaded rim 7 assembly, refer to instructions included with rim hardware. 2. Assemble spider net (13) to all rims. 3. Secure extension arm (7) to 3.5” pole section (8). Install pole cap (12). Measure rim to be regulation 10’ from the floor. 12 7 9 10 10 11 8 P/N 21165502 01/05 01/05 P/N 21165502 5

ملخص المحتوى في الصفحة رقم 6

INSTALLATION DIAGRAM WARNING TWO PERSON MINIMUM Assemble display products per diagram below. REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. 909180 44” Rectangle LIFETIME UNITS w/Slam Jam Rim Hardware Kit 201667 BOX OUT 909642 939183 44” Fan Backboard 46” Rectangle w/StandardRim w/Slam Jam Rim BACK Hardware Kit Steel Framed Acrylic 201672 Hardware Kit 201670 BEAST TITANIUM P/N 21165502 01/05 6