ملخص المحتوى في الصفحة رقم 1
Customer Service
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A Huffy Sports Company
WRITE IN YOUR MODEL NUMBER:
Portable Basketball System
Owners Manual
NOTICE TO ASSEMBLERS
ALL Huffy Sports basketball Systems, including those
SAFETY INSTRUCTIONS
used for DISPLAYS, MUST be assembled and ballasted
with sand or water according to instructions. Failure to
follow instructions could result in SERIOUS INJURY. It is
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
NOT acceptable to devise
ملخص المحتوى في الصفحة رقم 2
WARNING FAILURE TO FOLLOW THESE
WARNINGS MAY RESULT IN SERIOUS
INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know
and follow these rules for safe operation
of the unit. ·
See instruction manual for proper installation
and maintenance.
Use caution when performing dunk type
·
activities on this unit.
Do not hang from any part of unit, including
·
backboard, support braces, rim or net.
Do not slide, climb or play on base and/or
·
pole.
Surface beneat
ملخص المحتوى في الصفحة رقم 3
WARNING WARNING BACKBOARD IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL 1. Use a fork lift to remove unit from truck and carefully remove packing materials. 2. Remove backboard, lower pad (1) and both shroud covers (2 and 3). IMPORTANT! DO NOT REMOVE 3 STABILIZING STRAP AT THE REAR OF MAIN POST 2 AT THIS TIME! 1 REMOVE AND DISCARD SCREWS 3. Remove the three screws which hold base to pallet and carefully lay unit base forward down to floor. Discard screws.
ملخص المحتوى في الصفحة رقم 4
WARNING WARNING KEEP HANDS CLEAR Ballast Installation 4 4. Remove extension arm (4) from slide post brackets as shown. BACK VIEW 4 IMPORTANT! SET BRAKE AT THIS TIME. HERC03.EPS
211291 5. Cut stabilizing strap and set brake so unit will not roll. 6. Raise main post upward into playing position. HERC04.eps
211291 7. Tighten nut located at top of pole behind mast. HERC05.EPS
(Flat wrench (5) included.) 211291
5 4 P/N 211550A 07/01 HERC06.EPS
211291 HERC07.EPS
211291 WARNING KEEP HANDS
ملخص المحتوى في الصفحة رقم 5
WARNING WARNING WARNING BALLAST BALLAST 80 LB (36 KG) 80 LB (36 KG) BALLAST 80B LA B L (3L 6 A KS G)T 80 LB (36 KG) BALLAST BALLAST 80B LA B L (3L 6A KS G)T 80 LB (36 KG) BALLAST BALLAST BALLAST 160 LB (73 KG) 160 LB (73 KG) 8. Attach lower front pad (1) to unit as shown. 1 8 7 6 1 HERC08.EPS
211291 WARNING DO NOT USE UNIT WITHOUT BALLAST
AVERTISSEMENT MAY TIP OVER.
ADVERTENCIA HERC08A.EPS
211191 9. Install 640 lbs. (290 kg) of ballast. Secure
AVVERTENZA with straps.
ملخص المحتوى في الصفحة رقم 6
Install carriage bolt (39) through rim (11), washers (27) and (36) as shown. Tighten nut (42) completely. 11. Place nylon lock nut (31) about half-way up carriage bolt (39) as shown. 39 11 31 36 27 42 39 36 Attach bracket (37) to backboard and support structure 12. by inserting bolts (14) through washers (15) and top holes in bracket (37), Tighten nuts (16) completely. Peel 37 14 and stick foam pad (12) to front of board, behind bracket 15 (37) . 12 15 16 37 38 Insert inner bracket (38) into br
ملخص المحتوى في الصفحة رقم 7
Insert spacer (40) through rim assembly (11). Place rim assembly on bracket (37) so the cariage bolt (39) is inserted through hole on top of inner bracket (38). Install bolt (41), washers (36) and nut (31) through top holes 14. on bracket (37) as shown.Tighten completely. BOTTOM VIEW 11 36 11 40 37 38 39 40 36 36 31 41 Install rubber grommet (17), concave washer (18) and center lock nut (19) to bolt (39) as shown. 15. NOTE 39 Do not over tighten as rim will not flex properly. See leveling i
ملخص المحتوى في الصفحة رقم 8
RIM LEVELING INSTRUCTIONS: 16. Place level on rim (11) and adjust nut (31) until 11 level. Tighten nut (42) to set rim tension for playing. 31 42 20 Install cover plate (20) on rim (11) using self 17. tapping screws (21) as shown. 20 NOTE ORIENTATION OF COVER PLATE 37 21 Secure net (32) to rim (11). 18. 11 32 1 2 OUTSIDE VIEW 3 4 8 P/N 211550A 07/01
ملخص المحتوى في الصفحة رقم 9
19. Loosely assemble hardware to strut 28 (22). Mount strut (22) to backboard and finger tighten. Repeat for opposite side. 28 15 16 23 24 25 22 26 22 XHRC542A.EPS
211291 20. Secure struts (22) to extension arm (4). Completely tighten all strut hardware in Step 15 and Step 16. 30 31 22 30 29 4 22 9 07/01 P/N 211550A
WARNING WARNING
ملخص المحتوى في الصفحة رقم 10
Loosen nut located at top of post 21. behind pole mast (Refer to Steps 6 and 7) and carefully lower pole mast as shown. 22. Insert extension arm and backboard assembly into place and secure as shown. (Refer to Step 4)
WARNING TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. AVERTISSEMENT NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY.
ADVERTENCIA
AVVERTENZA 23. Lift backboard upward at an inclined
angle and position slip pin into slot ATENÇÃO as shown fo
ملخص المحتوى في الصفحة رقم 11
WARNING WARNING 24. Raise pole mast into playing position. 25. Re-tighten nut located at top of post behind mast. (Refer to Step 7) 26. Remove bolt at end of post brackets. Rotate extension arm and up into playing position and re-insert bolt to secure. XVAR07 .EPS
211492 11 07/01 P/N 211550A XVAR06.EPS
211492
ملخص المحتوى في الصفحة رقم 12
WARNING Height Adjustment 27. Remove tagged bolt at top of slide post.
WARNING DO NOT UNFOLD UNIT IF BACKBOARD IS NOT
AVERTISSEMENT ELEVATED MAY RESULT IN
WARNING DAMAGE TO THE UNIT. RE-INSERT TAGGED BOLT FOR STORAGE! FAILURE TO
ADVERTENCIA
AVERTISSEMENT DO SO MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.
AVVERTENZA
ADVERTENCIA
ATENÇÃO
AVVERTENZA
!WARNUNG
ATENÇÃO
WAARSCHUWING
!WARNUNG
ADVARSEL
ملخص المحتوى في الصفحة رقم 13
Ground Installation Place unit in desired location. Secure unit to 29. ground or flat surface as shown. FLAT SURFACE INSTALLATION IN-GROUND INSTALLATION 33 30 33 35 31 30 30 31 NOTE: 30 FLOOR SCREW NOT 35 HERC17.EPS
INCLUDED 211291 34 HERC16.EPS
211291 HERC18.EPS
211291 Regulation Rim Height is 10 Feet (3.05 m). 10 feet (3.05 m) 10FT_VAR.EPS
13 07/01 P/N 211550A 211492
ملخص المحتوى في الصفحة رقم 14
PARTS LIST Item Qty. Part No. Description Item Qty. Part No. Description 1 1 206597 Pad, Lower Front 23 2 206585 “L” Bracket 2 1 206592 Shroud, Right Cover 24 2 203153 Bolt, Hex 5/16”-18 x 3/4” 3 1 206593 Shroud, Left Cover 25 2 206116 Lockwasher, Split, 5/16” 4 1 206574 Extension Arm 26 4 203001 Nut, Hex, 5/16”-18 5 1 206556 Flat Wrench 27 1 203474 Washer, Flat 1/2” x 1” O.D. 6 5 206572 Bolt, Slotted Pan Head, 1/4”-20 28 2 205220 Weld Studs 7 5 206143 Washer, Locking 1/4” 29 1 200514 Bolt, Hex
ملخص المحتوى في الصفحة رقم 15
HARDWARE IDENTIFIER Item #24 (2) Item #25 (2) Item #26 (4) Item #28 (2) Item #30 (4) 206116/203305
203153 hex head bolt 5/16 x 3/4 203335 Washer 1 O.D. .4375 ID Washer, Lock 9/16 O.D. 5/16 -18 203160Weld Stud, rt. angle, 5/16 x 1-1/2 203001 Hex Head Locknut 5/16 Item #29 (1) 200514 hex head bolt 3/8-16 x 3 Item #35 (1) Item #36 (4) Item #42 (1) Item #31 (4) Item #27 (1) Item #39 (1) Item #40 (1) Item #41 (1) 15 07/01 P/N 211550A
