ملخص المحتوى في الصفحة رقم 1
A Action Sounds ction Sounds
Action Sounds Action Sounds
BASKETBALL
Model K9125 M Model K9125 odel K9125
www w www ww.fisher .fisher .fisher-price.com -price.com -price.com
1
ملخص المحتوى في الصفحة رقم 2
Consumer Information Consumer Information CARE CAUTION � The frame and net may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. This product contains small parts in Rinse clean with water to remove residue. Do not immerse this toy. its unassembled state. � To prolong the life of the net, store this toy indoors. Adult assembly is required. � Do not leave this toy outside in freezing weather. Water left inside the bas
ملخص المحتوى في الصفحة رقم 3
Parts Parts Hint: Some parts were placed inside the lower post for shipping. Upper Post Backboard 4 Rim 5 Collar Sound Box 6 Paddle Lower Post Ball Plug Base 3 1 #6 x / " (1.9 cm) Screw - 4 #8 x 2 / " (5.7 cm) Screw - 1 4 4 BOTH SHOWN ACTUAL SIZE Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten. Note: Label not shown 3
ملخص المحتوى في الصفحة رقم 4
Side Edge Assembly Assembly Curved End 7 4 Upper Post 2 1 5 5 6 6 Large Square Opening 4 Base 3 3 � Position the base as shown. 1 � Position the upper post so that the straight end is down and the curved end is up and facing away from the base. Proper label application will help to keep the label looking its best! Hint: For easier assembly, apply liquid soap or rub a candle or bar soap � Make sure the area where the label will be applied is clean and dry. Wipe around the bottom of the upper po
ملخص المحتوى في الصفحة رقم 5
Assembly Assembly Wall Backboard Rim Labels Soundbox 4 Groove 5 Upper Post Peg 6 5 Paddle � Lean the rim against a wall for support. 7 � Locate the pegs on each side of the rim and the grooves on the backboard. � Position the backboard with the label side facing up. � Fit the paddle onto the pegs on the soundbox, as shown. � Place your foot on the base to hold it steady and slide the backboard onto 1 � Insert the #8 x 2 / screw through the paddle and into the soundbox 4 the upper post at an angl
ملخص المحتوى في الصفحة رقم 6
Assembly Assembly Peg Peg Lower Post 4 Holes Rib 5 Groove 11 Base 6 � If the lever comes off, simply re-attach it. � Insert the peg on one side of the lever into the hole in the collar. 9 � Snap the other peg in the lever into the other hole in the collar. Assembly is now complete. IMPORTANT! Assembly of the lower post to the base is a Please refer to assembly step 2 to fi ll the base with water or approximately permanent assembly. 50 lbs. (22.7 kg) of sand (water and sand not included) to keep
ملخص المحتوى في الصفحة رقم 7
Adjusting The Rim Height Adjusting The Rim Height Backboard 4 Slots 5 Upper Post Lever 6 Lower Post Upper Post Base 1 3 � As assembled, the rim height is 3' (1 m). � To raise the rim height to 4', 5', or 6' (1.2 m, 1.5 m or 1.8 m), place your � To lower the rim height: while holding the upper post, push the lever on foot on the base and pull up on the backboard with both hands to remove the lower post down. Lower the upper post and push the lever into the slot the upper post from the base.
ملخص المحتوى في الصفحة رقم 8
Maintenance Battery Maintenance Battery Replacement Replacement Tip: We recommend the use of alkaline batteries for longer battery life! 1.5V x 3 "AAA" (LR03) Shown Actual Size � This toy includes an inflatable ball. If the ball becomes soft, inflate it with a standard, manual air pump with a standard air needle. Battery � The ball will contain the correct amount of air when its circumference Compartment measures about 19-20 inches (48-51 cm). Measure the circumference of the ball with a tape
