ملخص المحتوى في الصفحة رقم 1
#406 Woolim e-Biz Center, 170-5 Guro-dongGuro-gu, Seoul City, Korea.
TEL : +82-2-861-6691/2 FAX : +82-2-861-6693
Home page: www.servore.com E-mail: servore@servore.com
ملخص المحتوى في الصفحة رقم 2
#406 Woolim e-Biz Center, 170-5 Guro-dongGuro-gu, Seoul City, Korea. TEL : +82-2-861-6691/2 FAX : +82-2-861-6693 Home page: www.servore.com E-mail: servore@servore.com
ملخص المحتوى في الصفحة رقم 3
For your own protection, safety and to ensure the maximum service life of your new helmet please read this manual carefully before use. Misuse or abuse Note may result in injury or reduced protection and may also void your warranty. Safety is a personal responsibility. Servore endeavours to produce high quality safety products that meet or exceed relevant Standards and provide appropriate protection when used properly. Please help yourself and those a
ملخص المحتوى في الصفحة رقم 4
The appropriate available shade number markings and range are indicated on the product. Please ensure that the appropriate shade number is selected before welding. Used properly the ServoGlas 4000 provides eye and face protection to meet or exceed EN379 and EN175 and other relevant Standards where indicated. The following example illustrates these requirements. Please note this example is provided for illustration purposes only. The following parts are available from Servore and your auth
ملخص المحتوى في الصفحة رقم 5
0.05 msec - TIG welding (Pre-shading Tech.) Switching time (light-dark) 1. Solar Cell Panel 2. Sensor 3. LCD Filter Plate 0.06 msec - ARC, MIG, MAG welding 4. Sensitivity Control 5. Shade Control 6. Delay Switch Delay switch (dark-light) Slow : 0.3-0.6s Fast : 0.1-0.35s 7. Low Battery Lamp Inactivated Light shade #3 Light transmitting Activated Dark shade #9 ~ #13 Sensitivity control Adjustable UV/IR Protection Up to shade #13 Lithium battery 3V 2ea + Solar cells Power source Power A
ملخص المحتوى في الصفحة رقم 6
Where problems are experienced during welding at low currents The required filter dark state can be selected by [e.g. TIG] or there is a high level of ambient light please follow using the shade control. The ServoGlas 4000 these steps: First try adjusting the sensitivity control switch. If can be adjusted between shades 9 to 13 with this does not solve the problem hold the helmet close to the the embossed arrow on the dial indicating the target object and adjust the shade control completely
ملخص المحتوى في الصفحة رقم 7
To replace the protective inside cover plate the filter cartridge must be removed from the Always ensure that all maintenance procedures are conducted in a clean retaining guide frame. Always ensure this process is conducted in a clean dry place and dry place. take care not to drop the filter cartridge. To remove the filter cartridge from the retaining Use clean dry hands and avoid direct contact with any glass surfaces. frame gently expand the frame, you can then separate and remove the
ملخص المحتوى في الصفحة رقم 8
The Servo Glas 4000 uses two batteries to provide backup power. Always replace Your Servore welding helmet is strong and durable. It is designed to work in temperatures between -5C and +55C. Do not use your helmet in very hot conditions both batteries at the same time. Batteries should be replaced either: (a) Every three years or when the low battery warning lamp turns on (please also remove batteries and where temperatures exceed +65C. Always store your helmet in a clean dry place out
ملخص المحتوى في الصفحة رقم 9
The Servo Glas 4000 is designed for personal eye and face When working in the vicinity of other welders it is necessary to protection from harmful radiation, sparks and welding spatter adopt good industry standard practice and ensure a minimum produced under normal welding conditions. Please follow good distance of 1M between workers. Failure to do so may result in injury industry and safety practices and use additional protection where or malfunction of the auto darkening mechanism. ne
