ملخص المحتوى في الصفحة رقم 1
TE346W
Slim Weather Forecaster with
Indoor/ Outdoor Temperature,
Indoor Humidity and Atomic Clock
USER MANUAL
ملخص المحتوى في الصفحة رقم 2
INTRODUCTION Thank you for selecting a Meade Instruments Weather Forecaster. This device combines precise time keeping, monitoring and displaying of current temperature data from up to three remote locations (additional sensors are required). Meade Instruments is the world’s leading designer and manufacturer of telescopes for professional and amateur astronomers – famous for its innovative, high performance telescopes at affordable prices. Meade Instruments now brings that same passion for i
ملخص المحتوى في الصفحة رقم 3
INSTALLATION Communications between the main unit (receiver) and the remote sensor (transmitter) is wireless. This allows you to greater flexibility in choosing the location of remote sensor. The remote transmits data up to 164 feet (50 meters) over an open, unobstructed area. The remote sensor can be located either indoors or outdoors, allowing you chose where your data is obtained. NOTE: • It is critical to power the remote sensor BEFORE setting up the main unit. • It is critical to power u
ملخص المحتوى في الصفحة رقم 4
REMOTE TEMPERATURE SENSOR (TS01) FEATURES • Remote data transmission to the main unit via 433 MHz frequency • Single transmission channel • Case can be wall mounted using accessory hanger A. BATTERY COMPARTMENT AB • Holds two AAA-size batteries B. WALL-MOUNT RECESSED HOLE • Mounts the remote sensor on the wall BATTERY INSTALLATION NOTE: When the temperature falls below freezing point 32F° (0C°), battery voltage will drop which may result in reduced the transmission range. For optimum performan
ملخص المحتوى في الصفحة رقم 5
PLACEMENT • The remote sensor should be placed under eaves or a similar location with free air circulation, sheltered from direct sunlight and extreme weather. • Ideally, place the remote sensor over soil, rather than asphalt, which would cause false readings. • Avoid placing the remote sensor near sources of heat, such as chimneys and heating elements. • Avoid areas that collect heat from the sun and radiate heat, such as metal, brick or concrete structures, paving, and patios. • The i
ملخص المحتوى في الصفحة رقم 6
FRONT A B F E D C G I H REAR J K L 6
ملخص المحتوى في الصفحة رقم 7
A. WEATHER/ OUTDOOR TEMPERATURE window B. INDOOR TEMPERATURE/ HUMIDITY window C. CLOCK window D. DOWN (? ) button • Select the next available mode • Press and hold for 2 seconds to search for wireless signal from remote sensor. • Decrease parameters. E. UP (? ) button • Press to select the next available mode • Increase the parameters • In time with seconds display mode, press and hold for 2 seconds to activate/ deactivate atomic time signal search manually. • In time with weekday display m
ملخص المحتوى في الصفحة رقم 8
BATTERY INSTALLATION • Remove the battery door located at the back of the main unit. • Insert two (2) CR2032 lithium cell batteries and replace the battery compartment door. PLACEMENT • When mounting the main unit on the wall or vertical surface, fold the table stand back into the unit. • Make sure that the main unit is locating within the operating range of all remote sensors. • Ideally the main unit should be placed within line of sight of remote sensors. Avoid placing the main unit whe
ملخص المحتوى في الصفحة رقم 9
SEARCH FOR REMOTE SENSORS • The main unit can be manually activated to search for the signals from remote sensors by pressing and holding DOWN (? ) button. OPERATION • To select the indoor/ outdoor temperature mode, press UP (? ) or DOWN (? ) until the icon flashes with a beep sound alert. VIEWING REMOTE (CHANNEL) TEMPERATURE Static Display: • Press the CHANNEL button to select measurements from different remote sensors, each is MODE to a unique channel 1, 2 or 3. Channel Auto-Scan Dis
ملخص المحتوى في الصفحة رقم 10
COMFORT LEVEL INDICATION The main unit is capable of detecting and displaying the current indoor comfort levels of surrounding environment. The comfort level based on the combination of the current indoor temperature and humidity readings. The following comfort levels may be displayed: COMFORT (comfortable); WET (wet) and DRY (dry) Shows current Indicator Temperature Humidity condition displayed Range Range 20°C to 25°C 40%RH- Ideal relative humidity COM (68°F to 77°F) 70%RH and temperature
ملخص المحتوى في الصفحة رقم 11
• The atomic clock receiver is programmed that it will search for the time signal daily for 0:00, 3:00, 6:00, and 12:00 am. • To enable or disable the atomic time receiver, press and hold UP (? ) button for 3 seconds. If time reception is activated, a tower icon will start flashing. If reception is disabled, the tower icon will disappear. • If the time signal has not been received in 8 minutes, you may set the time manually. MANUAL SETTINGS To select the time mode, press UP (? ) or DOW
ملخص المحتوى في الصفحة رقم 12
SETTING THE ICE WARNING ALARM (PRE-AL) If Weekday (W) or Single day (S) alarm is MODE, the Ice Warning Alarm (Pre-AL) can be programmed. • Press ALARM button once to enter into the Ice Warning Alarm setting mode. The abbreviation OFF with a PRE-AL next to it will be displayed. • Press and hold ALARM button for two seconds. The number 30 will flash, meaning that if selected, the alarm will sound 30 minutes earlier than the Weekday or Single alarm. • Select the desired Ice Warning Alarm int
ملخص المحتوى في الصفحة رقم 13
PRECAUTIONS This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions: • Do not immerse the units in water. • Do not clean the units with abrasive or corrosive materials. They may scratch the plastic parts and corrode the electronic circuits. • Do not subject the product to excessive force, shock, dust, temperature, or humidity, which may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts. • Do not tam
ملخص المحتوى في الصفحة رقم 14
FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modification to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment had been tested an
ملخص المحتوى في الصفحة رقم 15
Battery Safety Instructions • Always purchase the correct size (2 x 1.5V AAA, 15A/15AC ANSI, LR6 IEC), (2 x ANSI/NEDA-5004LC, IEC-CR2032) and grade of battery most suitable for the intended use. • Replace all batteries of a set at the same time. • Clean the battery contacts and also those of the device prior to battery installation. • Ensure the batteries are installed correctly with regard to polarity (+ and -). • Remove the batteries from any weather station which is not to be used for a
ملخص المحتوى في الصفحة رقم 16
Meade Instruments Corp. 27 Hubble Irvine, CA 92618 U.S.A. © 2011 Meade Instruments Corp. All Rights Reserved. All user manual contents and information are subject to change.
