ملخص المحتوى في الصفحة رقم 1
www.zephyronline.com
Duo Is.
ADL-M90ASX
ADL-E42ASX
Layers Is.
ALL-M90ABX
ALL-M90AWX
ALL-E42AWX
ALL-E42ABX
RANGE HOOD - Installation instructions
ملخص المحتوى في الصفحة رقم 2
www.zephyronline.com HOTTE PER CUISINE - Notice d’utilisation...Pag. 25 CAMPANA EXTRACTORA - Manual de utilización...Pag. 48 CAPPA ASPIRANTE - istruzioni per l’uso...Pag. 73 - 2 -
ملخص المحتوى في الصفحة رقم 3
SAFETY INSTRUCTIONS..................................................................................................pag. 4 LIST OF MATERIALS...........................................................................................................pag. 7 DUCTING CALCULATION SHEETS...............................................................................pag. 9 HOOD SPECIFICATION..................................................................................................pag. 10 INSTALLAT
ملخص المحتوى في الصفحة رقم 4
www.zephyronline.com IMPORTANT SAFETY INSTRUCTIONS FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. IMPORTANT: Save these Instructions for the Local Electrical Inspectors use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. Take care when using cleaning agents or detergents. Suitable for use in household cooking area WARNING - To reduce the
ملخص المحتوى في الصفحة رقم 5
settings. B. Always turn hood ON when cooking at high heat or when fl ambeing foods ( i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè ). C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or fi lter. D. Use proper pan size. Always use cookware appropriate for the size of the surface element. E. Keep fan, fi lters and grease laden surface clean. F. Use high range setting on range only when necessary.Heat oil slowly on low to medium settin
ملخص المحتوى في الصفحة رقم 6
www.zephyronline.com through the fl ue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. D. Ducte
ملخص المحتوى في الصفحة رقم 7
Models: ADL-M90ASX / ADL-E42ASX Duct Covers Support Frame Assembly Blower Housing Control Range Hood Body Light Panel Light Bulbs Decorative Mesh Filters TYPE DESCRIPTION N° M4 1 + 1 A 1/8" x 1/4" 28 B 1/4" x 2-3/4" 4 C - 7 - List of Materials
ملخص المحتوى في الصفحة رقم 8
www.zephyronline.com Models: ALL-M90ABX / ALL-M90AWX / ALL-E42AWX / ALL-E42ABX Duct Covers Support Frame Assembly Glass Blower Housing Control Range Hood Body Light Bulbs Decorative Mesh Filters TYPE DESCRIPTION N° M4 1 + 1 A 1/8" x 1/4" 28 B 1/4" x 2-3/4" 4 C - 8 - List of Materials
ملخص المحتوى في الصفحة رقم 9
Maximum Duct Length: For satisfactory air movement, the total duct length should not exceed 100 equivalent feet. - 9 - Ducting Calculation Sheet
ملخص المحتوى في الصفحة رقم 10
www.zephyronline.com Models: ADL-M90ASX / ADL-E42ASX front of hood side of hood top of hood
- 10 - Hood Specifi cations
ملخص المحتوى في الصفحة رقم 11
Models: ALL-M90ABX / ALL-M90AWX / ALL-E42AWX / ALL-E42ABX front of hood side of hood top of hood - 11 - Hood Specifi cations
ملخص المحتوى في الصفحة رقم 12
www.zephyronline.com The following instructions are for installing the internal blower. CAUTION: To reduce the risk of fi re and electric shock, install this range- hood only with internal blower models MT-020 provided with the kit cod CBI-600A. For external and in-line blower preparation please turn to page 14. 1. Remove the (7) screws securing the remote motor support bracket to the motor housing and then remove the bracket. See Fig.1 2. Insert the 6” sheet metal fl ange in the motor a
ملخص المحتوى في الصفحة رقم 13
6. Attach the 6 pin male molex connector from blower wire to the 6 pin female molex con- nector located inside the blower housing. See Fig.6 7. Install the motor and bracket, inside the motor housing, completing the installation using the other screws (6 type B )that have been sup- plied. (Tot. 13 type B). Fig. 7 8. Connect 9 pin male molex connector from blower wire to 9 pin female molex connector on the capacitor wire. See Fig.8 WARNING! Place electrical wiring inside the blower hou- si
ملخص المحتوى في الصفحة رقم 14
www.zephyronline.com The following instructions are for preparing the hood for use with an ex- ternal or in-line blowers models CBE-1000 or PBN-1000A. CAUTION: To reduce the risk of fi re and electric shock, install this rangehood only with remote blowers rated maximum 6.2 A. For internal blower instructions please turn to page 12. 1. Break out the partially pre- cut circle in the lid, located on the remote motor sup- port bracket, using a fl at head screwdriver. Fig. 1 2. Remove the cover
ملخص المحتوى في الصفحة رقم 15
Note1: A cable lock (not included) may be re- quired by local codes. Please review local co- des for more information. 6. Reinstall the cover on the motor housing by following the instructions from step 2 in re- verse order. 7. Attach 6 pin male molex connectors to 6 pin female molex connectors inside blower hou- sing. See Fig. 6 Note2: Check local codes to determine mini- mum wire gauge. See manual included with external and in- line blower for instructions on installing the blower. - 15 -
ملخص المحتوى في الصفحة رقم 16
www.zephyronline.com WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating op- tion. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/certifi ed Silver Tape or Duct Tape. Some Ducting Options - 16 - Installation - Ducting Options
ملخص المحتوى في الصفحة رقم 17
MOUNTING HEIGHTS The range hood must be installed at a minimum height of 24 inches (61 cm) from the cooking surface. If a connecting duct work composed of
two parts is used, the upper part must be placed outside the lower part. Do not connect the range hood duct to
the same duct used to exhaust hot air or fumes from another appliance. Before proceeding with the assembly instructions remove the decorative mesh fi lters so that the range hood is easier to handle.
ملخص المحتوى في الصفحة رقم 18
www.zephyronline.com into the attic to connect after the hood is installed. Fig.11 3. Place assembled support frames on top of hood and secure it to the hood body using 8 type B screws. Fig.12 4. Place duct covers over assembled support frame until they rest on the hood body. Fig.13 Note! If you ordered a wood trim piece or re- circulating kit please refer to the instructions included inside the kits prior to installing the hood to the ceiling. - 18 - Installation - Mounting the Range
ملخص المحتوى في الصفحة رقم 19
5. Position hole template on the ceiling paying at- tention that the arrow is positioned on the same side as the range hood controls. - Make 4, holes in the ceiling and drive in (3 type C) screws without completely tightening them. Pay attention not to insert the screw into the hole marked with an X on the hole template Fig.14 6. Lift the hood assembly to the ceiling and align the top support frame with the (3) screws previously installed in the ceiling. - Rotate assembly slightly c
ملخص المحتوى في الصفحة رقم 20
www.zephyronline.com GENERAL • Carefully read the following important information regarding installation safety and maintenance. Keep this information booklet accessible for further consultations. POWER SUPPLY CONNECTION For connection to the power supply refer to the following: 1. Temporarily join the two duct covers by lifting the bottom one and then carefully securing it to the top by using adhesive tape. Fig. 17. Take care not to scratch the duct covers. 2. Break out the partially
