ملخص المحتوى في الصفحة رقم 1
Operating and Installation
Instructions
Ventilation System
DA 220-3
To prevent accidents
UV
and machine damage,
read these instructions
before
installation or use. M.-Nr. 06 438 010
ملخص المحتوى في الصفحة رقم 2
Contents IMPORTANT SAFETY INSTRUCTIONS Functional description Guide to the appliance Operation Turning on the fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Selecting the power level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Delayed Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Turning off the fan . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY INSTRUCTIONS Read these Operating Instructions carefully before installing or using the Ventilation System. This appliance is designed to vent This appliance is intended for cooking smoke and odors only. residential use only. Use the Be certain your appliance is appliance only for its intended properly installed and grounded by purpose. The manufacturer cannot a qualified technician. be held responsible for damages To guarantee the electrical safety of this caused by improper us
ملخص المحتوى في الصفحة رقم 4
IMPORTANT SAFETY INSTRUCTIONS This equipment is not designed for Use maritime use or for use in mobile Do not allow children to play with installations such as caravans or or operate the appliance or its aircraft. However, under certain controls. Supervise its use by the conditions it may be possible for an elderly or infirm. installation in these applications. Please contact the nearest Miele dealer or the Be careful when preparing a Technical Service Department with flambé beneath the hood. sp
ملخص المحتوى في الصفحة رقم 5
IMPORTANT SAFETY INSTRUCTIONS , WARNING - TO REDUCE , WARNING TO REDUCE THE RISK OF INJURY THE RISK OF A RANGE TOP TO PERSONS IN THE EVENT OF A GREASE FIRE: RANGE TOP GREASE FIRE, Never leave surface units OBSERVE THE FOLLOWING: unattended at high settings. SMOTHER FLAMES with a close Boilovers cause smoking and greasy fitting lid, cookie sheet, or metal spillovers may ignite. Heat oils slowly tray, then turn off the burner. on low or medium settings. BE CAREFUL TO PREVENT BURNS. Always turn the
ملخص المحتوى في الصفحة رقم 6
IMPORTANT SAFETY INSTRUCTIONS Installation Any fittings, sealant, or materials used to install the ductwork must , WARNING be made of approved non-flammable To reduce the risk of fire only materials. use metal ductwork. Never connect an exhaust hood to When installing the hood, follow the an active chimney, dryer vent, vent recommended minimum safety flue, or room ventilating ductwork. Seek distances between a Miele cooktop and professional advice before connecting the hood: an exhaust hood vent
ملخص المحتوى في الصفحة رقم 7
Functional description The ventilation hood works by air extraction. The air is drawn in and cleaned by the grease filters and directed outside. The hood comes equipped with a non-return flap. This flap automatically closes when the hood is turned off so that no exchange of outside air and room air can occur. When the hood is turned on, the air pressure of the exhaust fan automatically opens the flap blowing the inside air and cooking odors outside. 7
ملخص المحتوى في الصفحة رقم 8
Guide to the appliance 8
ملخص المحتوى في الصفحة رقم 9
Guide to the appliance a Cover plate g Light button This button turns the light on and off b Chimney and also dims the light. The lighting can be used independently c Canopy of the fan. d Grease filters h On/Off button e Control panel i Fan power level buttons Four fan speed selection. f Overhead lighting j Delayed Shut Down This button activates the Delayed Shut Down feature. The fan can be set to turn off automatically after either 5 or 15 minutes. k Grease filter button The indicator above to
ملخص المحتوى في الصفحة رقم 10
Operation Turning on the fan Delayed Shut Down If odors or smoke remain in the kitchen after cooking has been completed, the Delayed Shut Down feature can be selected to allow the hood to continue running for either 5 or 15 minutes. ^ Press the On/Off button. The fan runs at power level "2". The On/Off indicator lights. Selecting the power level ^ Press the Delayed Shut Down button while the fan is still running. Press once = 5 minute delay (left indicator lights) Press twice = 15 minute delay ^
ملخص المحتوى في الصفحة رقم 11
Operation Turning off the fan Turning the lighting on/off The overhead lighting can be turned on and off independently of the fan. ^ Press the On/Off button to turn the fan off. The indicator goes out. ^ Press the light button briefly to turn on the lighting. Automatic Safety Shut Off The light button indicator illuminates. The fan will turn off automatically ^ Press the light button briefly again to 10 hours after the last button was turn off the lighting. activated. The lighting however will r
ملخص المحتوى في الصفحة رقم 12
Operation Grease filter timer Checking the grease filter timer A timer monitors the hours of fan To check the percentage of time operation. The indicator for the grease already used: filter will light after 30 hours of operation. The grease filters must then be cleaned. After the grease filters have been cleaned and put in place, the grease ^ Press the On/Off button to turn the filter timer must be reset. fan on. ^ To do this, press the grease filter ^ Press the grease filter button. button for
ملخص المحتوى في الصفحة رقم 13
Operation Reprogramming the grease filter timer The grease filter timer is preset to 30 hours. This time can be lengthened or The indicator for the grease filter and shortened to 20, 30, 40 or 50 hours. one of the_ indicators will flash. – A time of 20 hours should be The lit_ indicator shows the programmed in kitchens with programmed time: frequent pan or deep frying. 1st indicator from the left = 20 hours – A time of 20 hours should also be 2nd indicator from the left = 30 hours programmed if
ملخص المحتوى في الصفحة رقم 14
Cleaning and care Stainless steel Before cleaning or servicing the hood, disconnect it from the power Stainless steel surfaces can be cleaned supply by either removing the fuse, using a non-abrasive stainless steel unplugging it from the outlet or cleaner. manually "tripping" the circuit To help prevent resoiling, a conditioner breaker. for stainless steel can also be used. Apply sparingly with even pressure. Cleaning the casing Controls ,Never use abrasive cleaners, scouring pads, steel wool, t
ملخص المحتوى في الصفحة رقم 15
Cleaning and care Grease filters ^ Clean the filters - by hand: use a scrub brush in The reusable metal grease filters warm water with a mild detergent. remove solid particles from the vented - in a dishwasher: place the filters in kitchen air (grease, dust, etc). the lower basket, making sure that the spray arm is not blocked. Depending on the detergent, cleaning the grease filters in a dishwasher may cause permanent The grease filters should be cleaned discoloration of the filter surface. ever
ملخص المحتوى في الصفحة رقم 16
Cleaning and care Changing the light bulb Before changing the light bulbs, disconnect the hood from the power supply by either removing the fuse, unplugging it, or manually "tripping" the circuit breaker. When in use halogen bulbs become extremely hot, and they can burn your hands. Do not attempt to change the bulbs until they have ^ Remove the outer ring,a. had sufficient time to cool down. ^ Support the glass,c, while Do not touch the bulb surface. detaching the circlip,b. Be careful Fingerpri
ملخص المحتوى في الصفحة رقم 17
After Sales Service In the event of a fault which you can not correct yourself please contact the Miele Technical Service Department U 1-800-999-1360 techserv@mieleusa.com V 1-800-565-6435 service@miele.ca When contacting the Technical Service Department, please quote the model and serial number of your appliance. These are shown on the data plate which is visible when the grease filter is removed. 17
ملخص المحتوى في الصفحة رقم 18
18
ملخص المحتوى في الصفحة رقم 19
Installation Instructions
ملخص المحتوى في الصفحة رقم 20
Structural support The ceiling mounting plate will support the weight of the hood. This ceiling plate must be attached to rigid structural framing that is supported in its entirety by the ceiling joists, or to the ceiling joists directly. Do not attach the plate directly to the ceiling by using anchors, mollies or toggle bolts. 20
