ملخص المحتوى في الصفحة رقم 1
Manual ND ISLA UL ing.qxd 6/05/2003 11:50 PÆgina 1
INSTRUCTIONS FOR USE AND
INSTALLATION INSTRUCTIONS
IKD 1157.1 GE-UL
ملخص المحتوى في الصفحة رقم 2
Manual ND ISLA UL ing.qxd 6/05/2003 11:50 PÆgina 2 • WARNING: TO REDUCE THE RISK OF A Dear client: RANGE TOP GREASE FIRE: Congratulations on your choice. We are sure a. Never leave surface units unattended at that this modern, functional and practical high settings. Boilovers cause smoking apparatus, made with top quality materials, and greasy spillovers that may ignite. Heat will fully satisfy your needs. oils slowly on low or medium settings. Please read every section of this b. Always tur
ملخص المحتوى في الصفحة رقم 3
Manual ND ISLA UL ing.qxd 6/05/2003 11:50 PÆgina 3 Index • Once the kitchen hood has been installed, ensure that the feed cable to the network is Page not in contact with any live metal edges. Description of the apparatus 3 • Avoid connecting the apparatus to conductors used exits for fumes produced Instructions for use 4 by a non-electric energy source. E.g.: Programming timer 4 boilers, chimneys, etc. • If the extractor fan is going to be used Cleaning and maintenance 4 simultaneously with
ملخص المحتوى في الصفحة رقم 4
Manual ND ISLA UL ing.qxd 6/05/2003 11:50 PÆgina 4 Instructions for use Cleaning and maintenance You may control the kitchen hood's workings When cleaning and doing maintenance, by operating the controls as shown in the make sure the safety instructions set out diagram. on page 2 are complied with. Cleaning the body of the kitchen hood • If your kitchen hood is made from stainless steel, use this material's specially designed 32 1 cleaners following the instructions mentioned in the product s
ملخص المحتوى في الصفحة رقم 5
Manual ND ISLA UL ing.qxd 6/05/2003 11:50 PÆgina 5 Problem solving Proceed with the following checks before calling the Technical Service: Problem Possible cause Solution The kitchen hood feed cable is not connected to Connect feed cable to the network. the network. The extractor fan ceases to function There is no electrical current in the network Check that the network has electrical current Filters are saturated with fat. Change or clean the active charcoal and/or metal filters, as the case
ملخص المحتوى في الصفحة رقم 6
Made in Europe Manual ND ISLA UL ing.qxd 6/05/2003 11:50 PÆgina 6 F .Nr********** U C ©L US LISTED ELECTRIC FAN Tec. Cod. XXXX Technical Network Lights/ Motor Power Network Code (V) Motor Volume Code Frecuency (Hz) (W) 3 22UL324IS 120 60 2x20 / 340 850 m /h KÜPPERSBUSCH reserves the right to make changes and corrections to its products as it deems necessary, without altering their basic characteristics. • WARNING: Improper grounding can Accesories supplied result in a risk of electric shock.
ملخص المحتوى في الصفحة رقم 7
Manual ND ISLA UL ing.qxd 6/05/2003 11:50 PÆgina 7 Installation with output vent Installation On installing the kitchen hood make sure Fig. 1 (Pag. 8) that the Safety Instructions set out on 1) Using the support (O), trace and drill the page 2 are complied with. points for fitting the lock screws (S) (Ø8 x 45) onto the ceiling. 2) Screw the support (O) into the ceiling with • WARNING: TO REDUCE THE RISK OF the lock screw (S) (Ø8 x 45). FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE 3
ملخص المحتوى في الصفحة رقم 8
Manual ND ISLA UL ing.qxd 6/05/2003 11:50 PÆgina 8 FIG.1 1) Using the support (O), trace and drill the Installation witouth output vent, with points for fitting the lock screws (S) (Ø8 x 45) active charcoal filters (Optional) onto the ceiling. When exterior gas extraction to the outside is 2) Screw the support (O) into the ceiling with not possible, then the kitchen hood may be the tirafondos-anclaje (S) (Ø8 x 45). set to purify the air by recycling it through 3) Mount the top inner body (A6
ملخص المحتوى في الصفحة رقم 9
Manual ND ISLA UL ing.qxd 6/05/2003 11:50 PÆgina 9 6) Fit the part (A) if the inner tube (not to the desired height. supplied) is Ø150 or (A) + (B) if it is Ø120. 12) Mount the part (A5) with the screws (A4) (M4 x 12) in the rectangle parts of the top 7) Attach the inner tube with a clamp (not inner body (A6). supplied) to (A) or (B) as the case may be. 13) Lift the upper tubecover (A8) up to the 8) Introduce the upper tubecover (A8) into the desired height and fix it to the top group with l
