Greenheck Fan SMD-302M دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Model SMd-302M
Smoke dampers
Steel Airfoil Blades
UL 555S Leakage Class II
APPLICATION
Model SMD-302M meets the requirements for
Model SMD-302M is a leakage rated modulating smoke damper smoke dampers established by:
with class II leakage. The SMD-302M serves the function of both
National Fire Protection Association
a control damper and smoke damper. High strength airfoil blades
NFPA Standards 92A, 92B, 101 & 105
insure lowest resistance to airflow in HVAC systems with velocities
IBC Inte

ملخص المحتوى في الصفحة رقم 2

Pressure drop data SMd-302M This pressure drop testing was conducted in accordance with AMCA Standard 500-D using the three configurations shown. All 3 3 data has been corrected to represent standard air at a density of .075 lb/ft (1.201 kg/m ). Actual pressure drop found in any HVAC system is a combination of many factors. This pressure drop information along with an analysis of other system influences should be used to estimate actual pressure losses for a damper installed in a given HVAC

ملخص المحتوى في الصفحة رقم 3

5D 6D AMCA 5.2 Pressure drop SMd-302M 5D 4 (W) (H) D 3.14 36x36 12x48 * Sizes are in inches. 12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36in. x 36 in. (914mm x 914mm) 12in. X 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm) Velocity Pressure Drop Velocity Pressure Drop Velocity Pressure Drop Velocity Pressure Drop Velocity Pressure Drop (fpm) (in. wg) (fpm) (in. wg) (fpm) (in. wg) (fpm) (in. wg) (fpm) (in. wg) 500 0.03 500 0.01

ملخص المحتوى في الصفحة رقم 4

AMCA 5.3 Pressure drop SMd-302M 5D 6D 5D 4 (W) (H) D 3.14 24x24 * Sizes are in inches. 12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36in. x 36 in. (914mm x 914mm) 12in. X 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm) Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) Velocity (fpm) (in. wg) 500 0.01 500 0.01 500 0.0

ملخص المحتوى في الصفحة رقم 5

5D 6D 5D 4 (W) (H) D 3.14 AMCA 5.5 Pressure drop SMd-302M 36x36 12x48 24x24 12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36in. x 36 in. (914mm x 914mm) 12in. X 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm) Velocity Pressure Drop Velocity Pressure Drop Velocity Pressure Drop Velocity Pressure Drop Velocity Pressure Drop (fpm) (in. wg) (fpm) (in. wg) (fpm) (in. wg) (fpm) (in. wg) (fpm) (in. wg) 500 0.04 500 0.03 500 0.03 500 0.

ملخص المحتوى في الصفحة رقم 6

Application data damper Sideplate and Sleeve dimensional data The drawings below illustrate the factory standard sideplate and sleeve mountings for the SMD-302M. The standard "A" di- mensions listed in the table provide adequate space for the mounting of actuators and controls. 3 If space constraints are a problem the "A" dimension can be varied between 5 /8 in. (136mm) and 12 in. (305mm). 1 1 /2" max. 1 1 /2 in. max. Sleeve 1 1 /2" max. Sideplate "A" dimension in. (mm) Sleeve 3 3 /4" Sideplate

ملخص المحتوى في الصفحة رقم 7

damper Sizing Information Dampers larger than maximum single section size are supplied as a factory assembly of two or more sections of equal size. The following figures show damper sections and assemblies that have been qualified for operation with a single actuator. Larger sizes can be accommodated using multiples of these assemblies. Double Section Single Section 50 in. 50 in. (1270mm) (1270mm) 50 in. (1270mm) 96 in. (2435mm) 32 in. (813mm) 32 in. (813mm) 64 in. (1626mm) 32 in. (813m