ملخص المحتوى في الصفحة رقم 1
Kramer Electronics, Ltd.
USER MANUAL
Model:
WP-211DS
Wall Plate
ملخص المحتوى في الصفحة رقم 2
Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 1 3.1 About the Power Connect Feature 1 3.2 Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP) 2 3.3 About the WP-211DS 2 3.4 Recommendations for Achieving the Best Performance 3 4 Your WP-211DS 3 5 Using the WP-211DS 5 5.1 Installing the WP-211DS 5 5.2 Wiring the CAT5 LINE IN / LINE OUT RJ-45 Connectors 6 5.3 Connecting the WP-211DS 7 5.4 Operating using the Default Master Source Signal Selection 8 5.5 Con
ملخص المحتوى في الصفحة رقم 3
ADDENDUM (this data is included at the end of the Overview section) This addendum adds the following information to the user manual: Caution – No operator-serviceable parts inside unit. Warning – Use only the Kramer Electronics input power 1 wall adapter that is provided with this unit . Warning – Disconnect power and unplug unit from wall before installing or removing device or servicing unit. 1 For example: model n
ملخص المحتوى في الصفحة رقم 4
Introduction 1 Introduction Welcome to Kramer Electronics (since 1981): a world of unique, creative and affordable solutions to the infinite range of problems that confront the video, audio and presentation professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better! Our 1 350-plus different models now appear in 8 Groups , which are clearly defined by function. 2 Congratulations on purchasing your Kramer WP-211DS wall plat
ملخص المحتوى في الصفحة رقم 5
Overview The other unit is fed over the same CAT5 cable. The Power Connect feature applies as long as the CAT5 cable is heavy gauge cable (that is, it can carry power). The distance does not exceed 50 meters on standard cable. For a distance of 100 meters, separate power supplies must be connected to the transmitter and to the receiver simultaneously, unless using heavy gauge CAT5 cable. 3.2 Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP) The decision whether to use shielded
ملخص المحتوى في الصفحة رقم 6
Your WP-211DS 3.4 Recommendations for Achieving the Best Performance Achieving the best performance means: Connecting only good quality connection cables, thus avoiding interference, deterioration in signal quality due to poor matching, and elevated noise levels (often associated with low quality cables) Avoiding interference from neighboring electrical appliances that may adversely influence signal quality, and positioning your WP-211DS away from moisture, excessive sunlight and d
ملخص المحتوى في الصفحة رقم 7
Your WP-211DS Table 1: WP-211DS Front Panel Features # Feature Function 1 XGA INPUT 2 HD15F Connector Connects to the computer graphics source 2 2 DEFAULT SELECT Switch Slide to left for input 2, slide to right for input 1 3 IN 2 Green LED Lights when the XGA INPUT 2 source is active 4 IN 1 Green LED Lights when the XGA INPUT 1 source is active 5 XGA INPUT 1 HD15F Connector Connects to the computer graphics source 1 6 AUDIO IN 2 mini plug Connector Connects to audio source 2 7 AUDIO I
ملخص المحتوى في الصفحة رقم 8
Using the WP-211DS 5 Using the WP-211DS For details of how to: Install your WP-211DS, see section 5.1 Wire the CAT5 LINE IN / LINE OUT RJ-45 connectors, see section 5.2 Connect your WP-211DS, see section 5 .3 Select the default master source signal, see section 5.4 Connect the REMOTE connector, see section 5.5 You can use your WP-211DS, for example, in a conference room, as the example in Figure 3 illustrates: Figure 3: Example of a Conference Room WP-211DS Insta
ملخص المحتوى في الصفحة رقم 9
Using the WP-211DS 5.2 Wiring the CAT5 LINE IN / LINE OUT RJ-45 Connectors Table 3 and Figure 4 define the UTP CAT5 PINOUT, using pin to pin wiring to connect the WP-211DS output to the TP-120 input: Figure 4: CAT5 PINOUT Table 3: CAT5 PINOUT TP-120 CAT5 WP-211DS INPUT CAT5 OUTPUT PIN Wire Color PIN Wire Color 1 BLUE(--) 1 BLUE(--) 2 BLUE(+) 2 BLUE(+) 3 GREEN(--) 3 GREEN(--) 4 +12VDC 4 +12VDC 5 GND 5 GND 6 GREEN(+) 6 GREEN(+) 7 RED(--) 7 RED(--) 8 RED(+) 8 RED(+)
ملخص المحتوى في الصفحة رقم 10
Using the WP-211DS 5.3 Connecting the WP-211DS To connect your WP-211DS, do the following: 1. Connect a computer graphics (master) source to the XGA INPUT 1 HD15F connector and to the AUDIO IN 1 3.5mm mini jack, for example, using a 1 Kramer C-GMA/GMA cable . 2. Set the DEFAULT SELECT switch to IN 1 (the factory preset default) or IN 2, as section 5.4 describes. 3. Connect a second computer graphics source to the XGA INPUT 2 HD15F connector and to the AUDIO IN 2 3.5mm mini jack, for ex
ملخص المحتوى في الصفحة رقم 11
Using the WP-211DS 5.4 Operating using the Default Master Source Signal Selection The DEFAULT SELECT switch is factory preset to IN 1 and the WP-211DS will detect the presence of the master source signal at the XGA INPUT 1 connector. If you connect active sources to both the XGA INPUT 1 and the XGA INPUT 2 connectors, the source at the XGA INPUT 1 connector takes priority over the source at the XGA INPUT 2 connector and it is routed to the XGA OUT and the AUDIO OUT connectors (audio follo
ملخص المحتوى في الصفحة رقم 12
Using the WP-211DS 5.5 Connecting the REMOTE Connector You can force the routing of one of the 2 inputs to the XGA output by remote control. To do so, connect the appropriate REMOTE input terminal block 1 connector pins to a dry contact switch . For example, as Figure 6 illustrates, to route REMOTE IN 1 to the XGA output, connect PIN 1 to the Ground. To route REMOTE IN 2 to the XGA output, connect PIN 2 to the Ground pin. Do not connect both the REMOTE IN 1 and the REMOTE IN 2 to the Grou
ملخص المحتوى في الصفحة رقم 13
Technical Specifications 6 Technical Specifications Table 4 includes the technical specifications: 1 Table 4: Technical Specifications of the WP-211DS INPUTS: 2 XGA on HD15F connectors 2 unbalanced stereo audio on 3.5 mm mini audio connectors OUTPUTS: 1 XGA (RGBHV) on a 10 PIN terminal block connector 1 XGA on an HD15F connector (input #1 loop) 1 unbalanced stereo audio on a 3 PIN terminal block connector 1 CAT5 (for video) on an 8 PIN terminal block connector MAX. OUTPUT LEVEL: VIDEO:
ملخص المحتوى في الصفحة رقم 14
LIMITED WARRANTY Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase. WHO IS PROTECTED? Only the first purchase customer may enforce this warranty. WHAT IS COVERED AND WHAT IS NOT COVERED Except as below, this warranty covers all defects in material or workmanship in this product. The followi
ملخص المحتوى في الصفحة رقم 15
For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com, where updates to this user manual may be found. We welcome your questions, comments and feedback. Safety Warning: Disconnect the unit from the power supply before opening/servicing. Caution Kramer Electronics, Ltd. Web site: www.kramerelectronics.com E-mail: info@kramerel.com P/N: 2900-78 REV 3
