ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
Important! – Please Read This Manual Before Installing! Congratulations on your purchase of a Voyager AOM703 LCD Observation Monitor. With proper installation and use, your AOM703 is designed to provide you with years of trouble-free operation. This manual contains important information required to properly install and operate the unit. Please read this manual thoroughly before beginning. All Voyager Observation products are strictly intended to be installed as a supplement aid to standard r
ملخص المحتوى في الصفحة رقم 3
ملخص المحتوى في الصفحة رقم 4
CONTROLS AND OPERATION S + – S 1 2 3 4 5 1. Power/Stand-By mode: The Power / Stand-By button has two possible operation modes. a. Manual mode - Turned on manually by the user by pressing the Power button. b. Stand-By mode -Turned on by a stand-by trigger wire generally connected to the vehicles 12V reverse back up lights or turn signals. Manual Mode wiring - For manual mode operation, the AOM703 should be wired as follows: ACC (12V+) Red wire should be connected to the vehicles accessory feed.
ملخص المحتوى في الصفحة رقم 5
The power button features dual-illumination (bright and dim). In installations where the unit is not wired for Stand-by operation and power is applied to the unit, the Power Button will dimly glow when the unit is off, allowing the user to easily find the control in low light. Illumination switches to full intensity when the unit is turned on. 2. Source Input Select Button S S This control toggles the active display image back and forth between AV1, AV2 or AV3 inputs. 3. Day/Night Mode
ملخص المحتوى في الصفحة رقم 6
INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLATION: Before drilling, be sure that no cable or wiring is on the other side. Clamp all wires securely to reduce the possibility of them being damaged during installation and use. Keep all cables away from hot or moving parts, and electrically noisy components. Wiring Definitions: ¡ Power connection: Pin 1 ACC +12V (Red) Pin 2 Standby Reverse Trigger (Blue wire) Pin 3 Ground (Black wire) Pin 4 Audio Trigger (White wire) Pin 5 Standby Left
ملخص المحتوى في الصفحة رقم 7
5. Use the template provided on page 10 for proper placement of the junction box mounting holes. Use the #8 self-drilling screws (included) to secure the junction box in the desired location. The junction box can also be mounted using the 2”x 4” velcro strip (included). 6. There are 2 options for connecting the LCD monitor to the junction box. If the application is such that the monitor is in close proximity to the junction box, the AOM703 monitor can be connected directly to the junction b
ملخص المحتوى في الصفحة رقم 8
ملخص المحتوى في الصفحة رقم 9
REAR OBSERVATION INSTALLATION DISTANCE MARKER USE/INSTALLATION - PLACE INDICATOR MARKERS (CONE, BOX ANY REFERENCE OBJECT HANDY) BEHIND VEHICLE AS IN FIGURE A. - PLACE RANGE MARKER DECALS ON SCREEN OF MONITOR OVER IMAGE OF INDICATOR MARKERS ON GROUND BEHIND VEHICLE, AS VIEWED ON THE MONITOR SCREEN. - THIS GIVES YOU A VISUAL REFERENCE OF ACTUAL DISTANCE BEHIND VEHICLE, AS OBJECTS ARE VIEWED. INDICATOR MARKERS 1FT 2FT 5FT WIDTH OF VEHICLE FIGURE A S – + S FIGURE B 9
ملخص المحتوى في الصفحة رقم 10
10mm JUNCTION BOX MOUNTING TEMPLATE 10mm 10 175mm 155mm 9mm 5mm 60mm 14.8mm 30.4mm
ملخص المحتوى في الصفحة رقم 11
® PANAVISE MOUNT TEMPLATE (OPTIONAL ACCESSORY) 0.25 2.00 0.25 2.50 2.00 0.25 2.50 11
ملخص المحتوى في الصفحة رقم 12
TROUBLESHOOTING SYMPTOM CAUSE SOLUTION No power No +12V accessory, No Replace circuit fuse, monitor has protection ground, mis-wired/reversed device built-in/reset, check ground connection, verify power is being supplied Video/No audio White audio trigger wire Connect to +12V ACC or reverse light circuit, not powered, Volume adjust turn volume adjustment up down Monitor does not Blue standby wire not powered Connect to reverse circuit +12V activate in Standby reverse trigger Negative/dark Low vo
ملخص المحتوى في الصفحة رقم 13
PRODUCT SPECIFICATIONS LCD panel specifications: Size/Type 7” (diagonal) /TFT LCD Brightness 350 nit (min) 420 nit (typ.) Contrast Ratio 200 (min) 300 (typ.) View Angles Top (12 o’clock): 30°(min) (@ CR³10) Bottom (6 o’clock): 50°(min) Horizontal: ±50° (min) Response Time Rise: 12ms (typ.) ; 50ms (max) Fall: 18ms (typ.) ; 60ms (max) Back light Type CCFL Back light Life 30k hrs (min) ; 40k hrs (typ.) Operation Temperature Range:-20°C to 65°C Storage Temperature Range:
