Metra Electronics 99-5822B دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION INSTRUCTIONS FOR PART 99-5822B
APPLICATIONS
2009-10 FORD F-150
LARIAT / KING RANCH / PLATINUM MODELS
(Not for NAV Equipped Models)
99-5822B - BLACK
99-5822AS – PLATINUM / ASH SATIN
99-5822CM - KING RANCH / CURLY MAPLE
99-5822MM – LARIAT / MILANO MAPLE
KIT FEATURES
• DIN Radio Provision With Pocket
• ISO Mount Radio Provision With Pocket
• Painted or Wood Grain
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Brackets • C) Radio Housing Trim Panel
• D) ISO Brackets • E)

ملخص المحتوى في الصفحة رقم 2

99-5822B TABLE OF CONTENTS Dash Disassembly - FORD F-150 2009-10 . ... ... .... ... .... ... .... ... .. . 1,2 Kit Preparation - FORD F-150 2009-10. ... .... ... .... ... .... .... ... ....3 Kit Assembly - DIN Radio Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - ISO Mount Radio Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . 5 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 *Note: Re

ملخص المحتوى في الصفحة رقم 3

99-5822B DASH DISASSEMBLY FORD F-150 2009-10 1 Disconnect the negative battery A terminal to prevent an accidental short circuit. 2 Unclip and remove the switch panel to the right of the cigarette lighter then remove the (1) 9/32” screw exposed. (Figure A) 3 Remove the rubber pad at the top of the radio trim panel then remove the (2) 9/32” screws exposed. (Figure B) 4 Unclip and pull the side panels con- B taining the a/c vents away from the radio trim panel. Note: It is not nec- essary to remo

ملخص المحتوى في الصفحة رقم 4

99-5822B DASH DISASSEMBLY FORD F-150 2009-10 E 6 Unclip and remove the hazard/airbag switch and driver info switch assem- blies from the factory radio trim panel. (Figure E) 7 Unclip and remove the cigarette lighter socket from the radio trim panel. (Figure F) 8 Remove (4) Torx screws securing the factory climate control to the radio trim panel. (Figure G) F 9 Remove (4) 9/32” screws to remove the factory radio. Continue to kit preparation. G FACTORY RADIO TRIM PANEL-REAR VIEW 2

ملخص المحتوى في الصفحة رقم 5

99-5822B KIT ASSEMBLY FORD F-150 2009-10 A 1 Clip the hazard/airbag switch and driver info switch assemblies into the radio housing in the same loca- tion as the factory radio trim panel. (Figure A) 2 Clip the cigarette lighter socket into the radio housing in the same loca- tion as the factory radio trim panel. (Figure B) 3 Secure the climate control into the radio housing using the factory B hardware in the same location as the factory radio trim panel. (Figure C) 4 Attach the (6) U style pa

ملخص المحتوى في الصفحة رقم 6

99-5822B KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the top (2) mounting holes off of the radio housing. Note: The notch in the housing should be on top. (Figure A) 2 Slide the included brackets onto the sides of the radio housings pocket from the back of the housing forward. (Figure B) 3 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure C) B 4 Slid

ملخص المحتوى في الصفحة رقم 7

99-5822B KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Cut and remove the top (2) mounting A holes off of the radio housing. Note: The notch in the housing should be on top. (Figure A) 2 Slide the included brackets onto the sides of the radio housings pocket from the back of the housing forward. (Figure B) 3 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure C) B 4 Slide the h

ملخص المحتوى في الصفحة رقم 8

99-5822B FINAL ASSEMBLY FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit). 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in rever