Greenheck Fan Ceiling Exhaust and Inline Fans 747680 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Document #474680
Model SP
® Model CSP
Ceiling Exhaust and Inline Fans
Installation, Operation and Maintenance Manual
Please read and save these instructions for future reference. Read carefully before attempting to assemble,
install, operate or maintain the product described. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result in personal injury and/or property damage!
Model SP Model CSP
Model SP is a direct drive ceiling exhaust fa

ملخص المحتوى في الصفحة رقم 2

Prepare the fan Remove Wiring Knockout Power Assembly Remove either top or side wiring knockout, If power assembly (motor, wheel, and scroll) is not depending on wiring installed in housing, insert the electrical plug into fan direction, by socket, then slide scroll end of power assembly into Electrical bending it back Access fan housing. Attach by using two sheet metal screws Panel and forth to provided. break tabs. B Model A Model Knockouts Ductwork Check ductwork to see if the fa

ملخص المحتوى في الصفحة رقم 3

To mount the ceiling radiation damper to fan, make sure Ceiling Radiation Damper (CRD) grille attachment tabs are facing down. Then place the inlet If fan is to be used in a fire resistive membrane part of the fan into the ceiling radiation damper collar, and ceiling, a ceiling radiation damper must be used. use self-tapping sheet metal screws (by others) to screw If the ceiling radiation damper is already mounted to through the damper collar and into the fan housing. If the the fan from

ملخص المحتوى في الصفحة رقم 4

Discharge Installation SP/CSP-B 50-200 Models 1 2 Insert SP-B box scroll tab into SP-B box Rotate plastic SP-B duct adapter (PN 474433) scroll slots. until the two SP-B mounting tabs fully engage into the two SP-B box mounting slots. SP-B Box Scroll Tabs SP-B Box Mounting Slots SP-B Box Scroll Slots SP-B Box Mounting Tabs 3 OPTIONAL Align the pins on the TR 6x4 adaptor to the duct pin hole on the SP-B 6-inch duct. Push until the adaptor snaps into place. TR 6x4 Pin SP-B Plastic Duct Pin

ملخص المحتوى في الصفحة رقم 5

AIRFLOW 1 (GOOD) 2 (GOOD) For Frame Construction: Install the Fan Position unit between Slots in the 1. For best joists. Position brackets brackets allow fine performance, adjustment Do not install such that bottom for flush fan in this area choose a location fit with edge of housing will wall/ceiling 45° 45° with the shortest opening be flush with finished possible duct run ceiling, and tighten the and minimum Fig. 1 adjustable mounting Fig. 3 number of elbows. brackets, shown in D

ملخص المحتوى في الصفحة رقم 6

Attach the Grille Fig. 8 1. If lighted grille is being used, plug wire into fan socket. If lighted grille and ceiling radiation damper are being used, plug wire from lighted grille into ceiling Fig. 9 radiation damper socket. Do not plug wire directly into the fan socket. Make sure the wire does not interfere with the ceiling radiation damper operation. 2. Attach grille with two screws provided. Make sure not to over tighten; over tightening will damage grille. 3. Slide attachment screw

ملخص المحتوى في الصفحة رقم 7

Flex Duct Other Installation Considerations Connections Ductwork and Noise Fiberglass ductboard is a better choice than metal ductwork for reducing fan noise and is highly recommended for low sound applications. Where metal duct is used, sound transmission can be reduced with flexible duct connections between the fan and the duct. Sound and Location The location of these fans must be taken into consideration before installation. In critical sound installations, insulated ductwork, flexible d

ملخص المحتوى في الصفحة رقم 8

Our Commitment As a result of our commitment to continuous improvement, Greenheck reserves the right to change specifications without notice. Specific Greenheck product warranties are located on greenheck.com within the product area tabs and in the Library under Warranties. Greenheck SP and CSP catalog provides additional AMCA Publication 410-96, Safety Practices for Users and information describing the equipment, fan performance, Installers of Industrial and Commercial Fans, provides availabl