ملخص المحتوى في الصفحة رقم 1
F30WC, F36WC, & F42WC SERIES
4-WAY CONVERTIBLE RANGE HOOD
READ AND SAVE THESE INSTRUCTIONS
! !
INTENDED FOR DOMESTIC COOKING ONLY
IMPORTANT
WARNING
For Non-ducted (Ductfree) Installation:
a) Purchase non-ducted filter separately.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
b) Remove and discard damper/duct connector and louver cover
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
(See Step 4) in “Prepare the Hood” Page 2. ,
FOLLOWING:*
c) Follow all steps except steps inside dotted lines.
ملخص المحتوى في الصفحة رقم 2
FIG. 1A TOOLS AND MATERIALS REQUIRED TOOLS ❏ Drill, electric or ratchet drive WALL CAP ❏ 1-1/4" Spade bit ❏ Common head and phillips head screwdriver WALL CAP FIG. 1B ❏ Pliers ❏ Tape measure or ruler and pencil 3-1/4" x 10" DUCT For Ducted Installations ONLY: ❏ Saber saw or drywall saw ❏ Metal snips MATERIALS ❏ Electrical wiring and supplies of type to comply with local ROOF CAP FIG. 1C codesFor Ducted Installations Only: ❏ Roof or wall cap ❏ Roof cement or caulk ❏ Duct and duct tape 3-1/
ملخص المحتوى في الصفحة رقم 3
PREPARING THE RANGE HOOD FIG. 2 KEYHOLE SLOTS 1. Unpack hood and check contents. You should receive: 1 - Aluminum Filter 1 - 3-1/4" x 10" Damper/Duct Connector (mounted inside of hood for shipping only) (Save screws for mounting.) WIRING BOX 1 - 7” Round Duct Plate (mounted on top of hood) (not shown) ALUMINUM COVER (Save screws for mounting.) FILTER 2. Remove 7” round duct plate from top of hood. Set duct plate aside - with mounting screws. 3. Remove wiring box cover. Under cover find: For Duct
ملخص المحتوى في الصفحة رقم 4
FIG. 8 INSTALLING THE 3-1/4” x 10” DUCT DUCTWORK FRONT OF CABINET NOTE THESE INSTRUCTIONS WILL FOLLOW THE PLANS MADE ON PAGE 2. START AT THE EXTERIOR AND RUN THE DUCT BACK TO THE RANGE HOOD. FOR BEST PERFORMANCE OF YOUR RANGE HOOD, 3-7/8" 3/8" 3/4" HORIZONTAL 1/8" USE THE SHORTEST POSSIBLE DUCT RUN AND A MINI- DUCTING AND MUM NUMBER OF ELBOWS. 5-1/4" 5-1/4" WIRING NEVER VENT A RANGE HOOD INTO AN ATTIC SPACE (Through Wall) 7-1/2" BECAUSE A BUILDUP OF GREASE WILL BECOME A FIRE CABINET BOTTOM HAZ
ملخص المحتوى في الصفحة رقم 5
FIG. 10 INSTALLING THE RANGE HOOD 16.Bring electrical cable through access hole drilled in wall or CONNECTOR bottom of cabinet. Provide 6" wire leads and install proper connector for type of cable being used. Remove lock nut from connector and let prepared cable project through cabi- net or wall opening so it is ready for installation into range hood. (FIG. 10) FIG. 11 17.Position hood in place so that: ELECTRICAL LINE a) Electrical line is routed through appropriate knockout open- ing. This ste
ملخص المحتوى في الصفحة رقم 6
SERVICE PARTS F30WC, F36WC, & F42WC SERIES RANGE HOOD 21 12 15 18 17 13 20 14 16 19 11 1 9 2 8 7 3 10 5 6 4 5 KEY NO. DESCRIPTION 1 Outlet Box Cover 2 #8 x 3/8 Sheet Metal Screw* 3 Bulb Holder with Wires 4 Light Lens 5 Screw/Nut Kit (Includes 2 - #10-16 x .500 screws and 2 - #10-16 sheet metal nuts) 6 Fan Blade 7 #6-32 Locking Nuts* (2 Required) 8 Motor Mounting Bracket 9 Motor Assembly (Includes Key Nos. 6, 7, and 8) 10 Aluminum Filter Non-Ducted Filter (purchase separately) 11 Filter Retaine
ملخص المحتوى في الصفحة رقم 7
7
ملخص المحتوى في الصفحة رقم 8
Major Appliance Warranty Information Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used, and maintained in accordance with the provided instructions. Exclusions This warranty does not cover the following: 1. Products with original serial numbers that have been rem
