ملخص المحتوى في الصفحة رقم 1
Home Theater Master
Home Theater Master
Universal Remote Control
Universal Remote Control
SL-8000
Operating
Manual
ملخص المحتوى في الصفحة رقم 2
Table of Contents Page Introduction 2 Battery Installation 3 A. To Open and Close Battery Compartment Cover 3 B. Low Battery Message 3 Using Your Remote Control 4 A. Function Table Reference 4 Function Tables 5 B. Preprogrammed Set Up 8 Three Digit Code Method 8 Auto Search Method 10 Recalling the Set Up Code Number 12 C. Operation 13 Device Buttons 14 Main Device Mode 15 Automatic Audio Mode 15 Backlighting 16 Advanced Features 17 A. Punch Through Controls 17 Volume “Punch Through”
ملخص المحتوى في الصفحة رقم 3
Introduction The Home Theater Master SL-8000 remote control is preprogrammed to operate over 1,000 Audio and Video components so that you can set it up by simply punching in a three digit code number that matches your equipment. The Home Theater Master SL-8000 remote control operates up to eight different audio and video devices in your home entertainment system. They are listed below: 1 TVs, Monitors, Video/LCD Projectors 2 VCRs, TV/VCR combination units 3 Cable boxes, Internet set-tops 4 Sat
ملخص المحتوى في الصفحة رقم 4
Battery Installation This remote control uses four AAA 1.5 V batteries. Please be sure to match the batteries with the (+) and (–) markings inside the battery compartment during installation. A:To Open and Close the Battery Compartment Cover 1 To open the battery cover, push the latch forward toward the top of the remote control, and lift the latch up. 2 To close the battery cover, slide the battery cover straight back in (toward the top of the remote) and push down until it “clicks” into pla
ملخص المحتوى في الصفحة رقم 5
Using Your Remote A: Function Table Reference AUD CD DVD DVD AUX 1 23 4 VCR CBL SAT TV 5 67 8 POWER 9 12 14 VOL CH MUTE T/ V 13 15 10 11 GUIDE MENU 22 21 PAUSE 16 R SEL F . E 19 20 18 PLAY F W STOP 17 PRE. 23 24 EXIT CH CH 1 2 3 FAV 25 26 27 37 SLEEP INFO 4 5 6 28 29 30 38 PRO.L 7 8 9 NEXT 31 32 33 39 3.CH +10 0 ENTER ALT 36 35 34 40 SHIFT TEST PIP 41 41 42 42 43 43 44 44 45 45 TUNER TUNER CD CD TAPE1 TAPE1 TAPE2 TAPE2 PHONO PHONO 46 47 48 49 50 VCR1 VCR1 VCR2/SAT VCR2/SAT LDP LDP AUX AUX TV
ملخص المحتوى في الصفحة رقم 6
Using Your Remote Function Table No. Button Name Audio Functions SAT Functions TV Functions 1-8 Device Name AUDIO (ON) SAT (ON) TV (ON) 9 Power On/Off (OFF) On/Off (OFF) On/Off (OFF) 10 Mute Mute Mute Mute 11 T/V Input Band/FM TV/SAT TV/Video 12 VOL Up Vol Up Vol Up Vol Up 13 VOL Down Vol Down Vol Down Vol Down 14 CH Up Preset + Ch. Up Ch. Up 15 CH Down Preset - Ch. Down Ch. Down 16 Up/Pause Center + Up Up 17 Down/Stop Center - Down Down 18 Right/F.F. Rear + Right Right/Picture 19 Left/Rew Rear
ملخص المحتوى في الصفحة رقم 7
Using Your Remote Function Table No. Button Name VCR Functions Cable Functions 1-8 Device Name VCR (ON) CABLE (ON) 9 Power On/Off (OFF) On/Off (OFF) 10 Mute Mute Mute 11 T/V Input VCR/TV Switch/A/B 12 VOL Up Vol Up Vol Up 13 VOL Down Vol Down Vol Down 14 CH Up Ch Up Ch Up 15 CH Down Ch Down Ch Down 16 Up/Pause Pause Up/Fine + 17 Down/Stop Stop Down/Fine - 18 Right/F.F. Fast Forward Right/Fine R 19 Left/Rew Rewind Left/Fine L 20 Sel/Play Play Select 21 Guide/I<< F. Adv./Slow< Guide/Recall 22 Menu
ملخص المحتوى في الصفحة رقم 8
Using Your Remote Function Table No. Button Name CD Functions DVD Functions AUX Functions 1-8 Device Name CD (ON) DVD (ON) TAPE (ON) 9 Power On/Off (OFF) On/Off (OFF) On/Off (OFF) 10 Mute Mute/Fader Mute/Rec Mute 11 T/V Input Random 12 VOL Up Vol Up 13 VOL Down Vol Down 14 CH Up Track +/Skip + Skip >>I 15 CH Down Track-/Skip - Skip I<< 16 Up/Pause Pause Pause Pause 17 Down/Stop Stop Stop Stop 18 Right/F.F. FF/Search + F.F. F.F. 19 Left/Rew REW/Search - REW REW 20 Sel/Play Play Play Play 21 Guide
ملخص المحتوى في الصفحة رقم 9
Using Your Remote B: Preprogrammed Set Up The Home Theater Master universal remote control can operate up to eight separate audio and video devices (equipment). To program the remote control for your devices, please use the following steps: Three Digit Code Method 1 Turn on the device you would like the remote control to operate, either manually or with your original remote control. 2Find the three digit Set-Up Code number for your device from the tables on pages (33~50). Example: To set up t
ملخص المحتوى في الصفحة رقم 10
Using Your Remote Note: SET appears in the LCD for 20 seconds to indicate that the remote control is ready to be programmed. The following steps must be entered while SET appears in the LCD. 4 Point the remote control toward the device that was turned on in Step 1 and press in the first three-digit Set- Up Code number for that device using the number buttons (0-9) on the remote control. SET followed by the number will appear in the LCD. Your device will turn off when the correct Set-Up Code n
ملخص المحتوى في الصفحة رقم 11
Using Your Remote Auto Search Method Please use this method if none of the Set-Up Code numbers worked for your device during the standard set-up proce- dure or if the manufacturer or brand for your device is not listed in Set-Up Code Tables. 1 Turn on the device you would like the remote control to operate, either manually or with your original remote control. 2 Press the corresponding Device Button (TV, VCR, SAT, CBL, AUD, CD, DVD, or AUX) and the MUTE button, simultaneously. SET will appe
ملخص المحتوى في الصفحة رقم 12
Using Your Remote If you pass the correct Set-Up Code number, you can return to it by pressing the CHANNEL DOWN button, one Set-Up Code number at a time, until your device turns back on. Note: During programming, the signal for POWER ON and POWER OFF is located on the MUTE button. For devices that use separate POWER ON and POWER OFF buttons, pressing the MUTE button on the remote control during programming will only turn the device OFF. 4 Once the correct code is confirmed, press the Device
ملخص المحتوى في الصفحة رقم 13
Using Your Remote Recalling the Set-Up Code Number To display the three digit Set-Up Code number that was stored for a device. 1 Press the Device Button and the MUTE button, simultane- ously. SET will appear in the LCD. 2 Press the T/V button. The LCD will quickly flash the three digit Set-Up Code number that was stored for your device in that mode. 3Please write your Set-Up Code numbers in the chart below, for future reference. Set-Up Code Numbers: Audio Cable SAT CD TV DVD VCR AUX 12 12
ملخص المحتوى في الصفحة رقم 14
Using Your Remote C: Operation After you have programmed the remote control for your equipment, use the following procedures to operate your home entertainment system: 1 Press the Device Button that you wish to operate: e.g. to operate a TV, press the TV Device Button; to operate a VCR, press the VCR Device Button, etc. 2Aim the remote control at the device and press the POWER button to turn on the device. 3Press the buttons that send out the commands you desire. Note: Some audio/video devi
ملخص المحتوى في الصفحة رقم 15
Using Your Remote Device Buttons Any press of a Device button at the top of the remote control can perform the following functions: 1 Changes the Device mode AUD on the SL-8000 r DVD AUX emote control. AUD CD CD DVD AUX VCR CBL 2 Sends out a preprogrammed POWER ON command for a SAT SAT TV TV VCR CBL Device, if applicable. POWER POWER VOL VOL CH CH 3 Sends out a joined selection. MUTE T/ V MUTE T/ V 4 Toggles between the Main Device mode and the Automatic GUIDE MENU GUIDE MENU Audio mode if t
ملخص المحتوى في الصفحة رقم 16
Appendix A:Assignment of Audio/Video Equipment Please use the following listing to locate the correct Set-Up Code Tables for your equipment: AUDIO Set-Up Code Table: Audio Receivers, Preamplifiers, Surround Processors Satellite Set-Up Code Table: DSS, Primestar, DBS, Echostar, C Band receivers TV Set-Up Code Table: TVs, Monitors, Video/LCD Projectors VCR Set-Up Code Table: VCRs, TV/VCR combination units CABLE Set-Up Code Table: Cable Boxes, Internet/TV Set-Tops CD Set-Up Code Table: CD Players
ملخص المحتوى في الصفحة رقم 17
Glossary Punch Through Advanced feature that enables you to operate Volume, Channel or Transport Control functions of one device while in another mode. Example: Audio Volume Control “Punch Through” gives you the ability to raise, lower and mute your Audio receiver volume while operating the remote control in the TV mode. Set-Up Code Number The three-digit number that is used to program the remote control for your particular manufacturer or brand of audio/ video equipment. Set-Up Code numbers ar
ملخص المحتوى في الصفحة رقم 18
Using Your Remote 4 Press the ENTER button. SAVE will flash twice and the LCD will return to AUDIO indicating that the joined function has been stored. Every time that the Device button is pressed it will also emit the joined function. To erase a joined function from a Device button: 1 Press the AUDIO and ENTER buttons simultaneously on the remote control. JOIN will appear in the LCD. 2 Press the Device button that you would like to erase a joined function. CLEAR will flash and INPUT wil
ملخص المحتوى في الصفحة رقم 19
Advanced Features After you set-up the remote control to operate your equipment, you can also program advanced features on the remote control. The advanced features are designed to enhance the use of the remote control with your home entertainment system. A: Punch Throughs Volume Control “Punch Through” You can program the remote control so that either the AUDIO or TV Volume Control (VOLUME UP, DOWN AND MUTE) will also operate in other modes on the remote control. Example: Raise, lower and mute
ملخص المحتوى في الصفحة رقم 20
Glossary Cursor Control Buttons that correspond to the UP, DOWN, LEFT, RIGHT, SELECT, GUIDE, MENU and EXIT functions of your audio/video equipment. Device Audio or video equipment, e.g. Television, VCR, Cable box, Audio receiver, Satellite receiver, etc. Device Button Any of the eight buttons located at the top of the remote control labeled AUD, CD, DVD, AUX, SAT, TV, VCR and CBL. Device Buttons are used to select modes of operation and to program the remote control. Joining Transfer of a functi
