ملخص المحتوى في الصفحة رقم 1
RMC-90 REMOTE CONTROL
PANEL FOR SE-800
User s Guide
http:// www.datavideo-tek.com
Rev: 091105
ملخص المحتوى في الصفحة رقم 2
Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit in or near water. 5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage. 6. Slots and openings on the cabinet top, back, and bottom are p
ملخص المحتوى في الصفحة رقم 3
Service and Support It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideo-tek.com for answers to common questions, support requests or contact your local office below. Datavideo Corporation (USA) 12300-U East Washington Blvd., Whittier, CA 90606 USA Tel: +1 562 696 2324 contactus@datavideo.us www.datavideo.us Datavideo Technologies Europe B
ملخص المحتوى في الصفحة رقم 4
Warranty Datavideo warrants that the equipment it manufactures shall be free from defects in material and workmanship for a period of 12 months from the date of product purchased. If equipment fails due to such defects, Datavideo will, at its option, repair or provide a replacement for the defective part or product. Equipment that fails after the warranty period, has been operated or installed in a manner other than that specified by Datavideo, or has been subjected to abuse or modificatio
ملخص المحتوى في الصفحة رقم 5
CONTENTS INTRODUCTION 5 WHAT S IN THE PACKAGE 5 CONTROL PANEL 6 REAR PANEL CONNECTION 10 MORE PERIPHERALS 12 4
ملخص المحتوى في الصفحة رقم 6
Introduction RMC-90 is a Remote Control Panel especially designed to work with SE-800 control panel simultaneously. RMC-90 provides a wired remote function of video channel selection keys, programmable effect function keys, T-Bar controlm ost of the control key functions from SE-800. It includes a Tally control for the Datavideo TLM-404 LCD panels and three GPI triggers to control Datavideo DV Bank. What s in the Package 1. RMC-90 unit 2. 15-pin D-sub TLM-404 LCD TALLY control cable 3.
ملخص المحتوى في الصفحة رقم 7
Control Panel Audio Select for channel A, B, C or D and A+V function key This row of selector buttons has a internal LED to show which input channel is active. If the A+V function key is engaged (LED on), the audio source channel selected on the Main Source bus is automatically selected. If A+V is not engaged, the input source is user selectable. Please refer to the Front Panel section of SE-800 instruction manual for a more detailed description. 6
ملخص المحتوى في الصفحة رقم 8
Video Main-source and SUB-source Select for channel A, B, C or D and BK (Background) function key It is used to select which of the four video input channels or background will be selected as Main Source and which of the four video input channels or background will be transitioned to or used as a sub source in an effect. For more information, please refer to the Front Panel section of SE-800 instruction manual. 7
ملخص المحتوى في الصفحة رقم 9
GPI-1 to GPI-3 Enable the three terminals GPI trigger output on rear panel for video play-pause control of Datavideo DV Bank F1-F10 and F11-20, F21-30 Control of the 30 users programmable preset locations for storing customized effects and transitions. The numbered buttons 1-10 above access 10 locations. To access F11 to F20, you need to first press the F11-20 button until the LED is lit, then press one of the single numbered buttons to access presets F11-F20. To access F21-F30, please
ملخص المحتوى في الصفحة رقم 10
T-bar is for performing effect transitions manually. It can be either all the way up, all the way down, or anywhere in between. To enable SE-800 T-Bar, the T-Bar on RMC-90 need to be set at either end of its travel. PLEASE NOTE, T-Bar on RMC-90 CAN NOT CONTROL AN AUDIO ONLY FADE EFFECT, it controls only Video or Video with embedded audio effect. Each press on this button will Press to turn on LED to playback the pre-stored function enable the GPI Trigger key s effect sequentially i
ملخص المحتوى في الصفحة رقم 11
Rear Panel connection GPI Trigger outputs to control DV Bank Trigger o/p +5V o/p Ground 10
ملخص المحتوى في الصفحة رقم 12
Connect to Datavideo TLM-404 4 x4 TFT LCD or connecting an certain adaptor cable to control the Tally interface of video input source devices, such as Came GREEN The D-Sub 15-pin connector works Video RED LED AMBER LED LED by closing contacts between a (On Air - Live) (Next - Cued) Channel (OffLine - Safe) ground pin and the corresponding A Pin 1 Pin 2 Pin 3 LED pin as following pin out table. B Pin 6 Pin 7 Pin 8 *. Do not give power to the pins. C Pin 11 Pin 12 Pin 13 D Pin 5
ملخص المحتوى في الصفحة رقم 13
More Peripherals Datavideo TLM-404 4 x4 TFT LCD panel Datavideo DV Bank Native DV recorder and GPI Trigger cable Built-in 120GB HDD for 9 hours native DV backup recording DV Bank is the industry-standard, stand-alone solution that allows video professionals to capture digital video (DV) content directly to a high performance disk drive-based system while shooting or anytime afterwards. Once your video is captured on the DV Bank, it can be quickly and easily accessed in a non-linear f
ملخص المحتوى في الصفحة رقم 14
Datavideo BAC-03 Balanced-Unbalanced Audio converter The BAC-03 is a bi-directional unbalanced to balanced and balanced to unbalanced audio converter, with four independent amplifiers providing stereo audio input and output. SPECIFICATIONS UNBAL to BAL output BAL to UNBAL output INPUT LEVEL -10dBv nominal 0dBm to +8dBm nominal INPUT IMPED 50K ohms 0K ohm GAIN +4 to +20dB -20dB to +18dB OUTPUT LEVEL 0 to +8dBm nom, +22dBm max -10dBv nom, +20dBv max OUTPUT LOAD 600 ohms or higher, balance
