ملخص المحتوى في الصفحة رقم 1
POWER
ON
OFF
HDTV ENCODER
INSTRUCTIONS
DM-JV600U
For Customer Use:
Enter below the Serial No. which is
located on the rear of cabinet. Retain
this information for future reference.
Thank you for purchasing this JVC product. Model No. DM-JV600U
Before operating this unit, please read the instructions
carefully to ensure the best possible performance. Serial No.
This instruction book is made from 100% recycle paper. LST0159-001C
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFEGUARDS 1.Read all of these instructions. 2.Save these instructions for later use. 3.All warnings on the product and in the operating instructions should be adhered to. 4.Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5.Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. 6.Do not use this appliance near water – for example, near a
ملخص المحتوى في الصفحة رقم 3
SAFETY PRECAUTIONS CAUTION ATTENTION RISK OF ELECTRIC SHOCK RISQUE D’ELECTROCUTION DO NOT OPEN NE PAS OUVRIR ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, NE PAS OUVRIR LE BOITER. DO NOT REMOVE COVER (OR BACK). AUCUNE PIECE INTERIEURE N’EST NO USER-SERVICEABLE PARTS INSIDE. A REGLER PAR L’UTILISATEUR. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL SE REFERER A UN AGENT QUALIFIE EN CAS DE PROBLEME. Le symbole de l’éclair à l’intérieur d’un trian
ملخص المحتوى في الصفحة رقم 4
Main Features Encoded to MPEG-2(ISO/IEC13818-2) Thank you for purchasing this Input SMPTE292M(1080i/720p) standard HDTV digital se- rial video signal, encode it to MPEG-2(ISO/IEC13818-2) HDTV ENCODER DM-JV600U. and output as DVB-ASI TS(Transport Stream). Supports SDI embedded Audio signal 2 channels Encodes SMPTE299M standard SDI embedded Audio sig- nal 2 channels to MPEG-1Layer 2 (ISO/IEC11172-3) and output as TS format. Dolby™ Digital (AC-3) pass through Compli- ance When Dolby™ Digital bitstr
ملخص المحتوى في الصفحة رقم 5
Table of Contents Main Features ...................................... 4 Introduction Table of Contents ................................. 5 Precautions .......................................... 6 Front Panel........................................... 7 Names and Functions Rear Panel ........................................... 8 Connecting ........................................... 9 Preparation Mounting to a Rack ............................ 10 Menu Flow Chart ................................
ملخص المحتوى في الصفحة رقم 6
Precautions Maintenance and operating environment Transportation Do not store or use this equipment in the following envi- Turn off the power and unplug the power cord from AC ronments. This will cause malfunctioning and damage. outlet before transportation. This may cause damage to power cord, fire or electrical • Locations beyond the allowable operating temperature shock. range of 5 °C and 40 °C. When moving or carrying the main unit, do no hold it • Locations beyond the allowable operat
ملخص المحتوى في الصفحة رقم 7
Front Panel 65 4 1 POWER POWER ON MULTI FORMAT HIGH DEFINITION ENTER ESC FAULT TELEVISION ENCODER OFF 7 32 [POWER] Power switch 1 About Display Switch to turn on/off power. After this is switched Normal display to ON, a “Now Initializing” will be displayed on the Display of front panel before normal screen is 5 HDTV ENCODER displayed. DM-JV600U After turning on the power, it may take 2 sec- Memo Memo onds before display light up. Press the 8 / 9 buttons Display the control set- [ESC] button 2
ملخص المحتوى في الصفحة رقم 8
Rear Panel 8 9 0 ! @ # $ AC 120V ~ 50 Hz/60 Hz IN MONI 2 1 RS-232C HD- OUT SDI ASI OUT REF IN(D1) AES/EBU IN [AC IN] Power input terminal 8 [AES/EBU IN] Audio signal input terminal # Use the power cord supplied to connect to an AC (BNC) 120 V 50 Hz/60 Hz outlet. Input terminal for digital audio signal (PCM or Dolby™ Digital bitstream). Connect to the digital au- [HD-SDI IN] Video signal input terminal (BNC) 9 dio signal output terminal of the device outputting Input terminal for HD serial di
ملخص المحتوى في الصفحة رقم 9
Connecting One example of the basic systems using this unit is described below. Turn OFF the power of all devices before connecting or disconnecting. HDTV VTR AUDIO VIDEO INPUT AUDIO INPUT / AUDIO MONITOR SELECT INPUT POWER SDI CH1 CH2 CH3 CH4 SIF AUDIO AES/EBU ON I MONITOR L CH1 CH2 CH3 CH4 LINE ANALOG R CH1 CH2 CH3 CH4 CPN Synchronized Signal OFF O REF signal Generator CH1 CH2 CH3 CH4/TRACKING SEARCH VAR PLAYERRECORDER R P R P R P R P COUNTER RESET VCON REMOTE dBOVER dB dBOVER dB dBOVER dB d
ملخص المحتوى في الصفحة رقم 10
POWER ON OFF POWER ON OFF Mounting to a Rack By making use of the hole on inner side of front panel, this unit can be mounted to EIA rack. Caution Caution • When mounting this unit to rack, mount the L shape bracket to both ends of the rack to ensure strength. • When mounting to the rack, Remove the foot mount it in the way such that this unit will not protrude out from the rack. (The depth of the rack should Foot be at least 700 mm) Remove the front panel EIA Rack Mount this unit to rack using
ملخص المحتوى في الصفحة رقم 11
Menu Flow Chart The menu of this unit consists of 3 level of menus namely “Main menu”, “Sub menu” and “Setting items”. Display screen Menu Item Main Menu Sub Menu Setting HDTV ENCODER DM-JV600U ENTER • Video Rate • Asp ENTER ENTER ENTER • 32Pulldown Main Menu Configuration Menu • Audio Mode + Configuration Menu + Operate Param Menu ESC ESC ESC • Audio Rate • Start Setting of the encoding bit rate/starting ☞ Page 12 • Stop method of encoding/various parameters, “Operate Param Menu” saving and
ملخص المحتوى في الصفحة رقم 12
Menu Setting Configuration Menu : Default setting Item Setting value Content Operate Param Memo Memo Menu Video Rate 9000kbps Set the bit rate of the encoded video signal. When the Audio Enable un- der the Initial Param Menu to The setting value can be set in 10 kbps step. screen is set to ON, the up- 20000kbps per limit value of Video to Rate is 40000kbps When the Audio Format un- der the Initial Param Menu Asp When the Video Mode Set the horizontal size of the encoded video s
ملخص المحتوى في الصفحة رقم 13
Configuration Menu : Default setting Item Setting value Content Initial Param Menu Control Mode Local Set the operation mode of this unit. Remote Local : Set to this mode when operating this unit using the buttons on the front panel. Remote : Set to this mode when using RS-232C terminal $ on the rear panel to perform remote control of this unit. Start Mode Auto Set the starting mode of encoding. Manual Auto : Start the encoding automatically. Manual : Start the encoding using t
ملخص المحتوى في الصفحة رقم 14
Menu Setting Configuration Menu (continued) : Default setting Item Setting value Content Initial Param Menu PSI Enable ON Set the PSI (Program Specific Information) to ON/ OFF OFF. ON : PAT and PMT will be output. OFF : PAT and PMT will not be output. PAT TS ID 0001 Set the ID of PAT TS. to PAT TS ID is the Transport Stream ID within PAT. 0001 PAT (Program Association Table) is the correspondences to table of Program number and PMT PID. FFFF PMT PID 0010 Set the PMT Packet ID
ملخص المحتوى في الصفحة رقم 15
Configuration Menu (continued) : Default setting Item Setting value Content Initial Param Memo Memo Menu Audio Stream ID C0 Set the ID of Audio PES stream. This setting is disabled when Audio Format under to the Initial Param Menu C0 screen is set as DD-PT (Dolby™ Digital Pass Through). to (Fixed as 0xBD) DF Video Copyright OFF Set the copyright flag of Video PES. ON OFF : Set the copyright flag of Video PES to OFF. ON : Set the copyright flag of Video PES to ON. Video Or
ملخص المحتوى في الصفحة رقم 16
How to Change Menu Setting The various features of this unit can be set using the menu. The setting value, which is stored in the internal memory will reappear upon turning on the power. Display 8 / 9 / ; / :buttons Example Remote control of this unit POWER POWER ON MULTI FORMAT can be achieved by using HIGH DEFINITION ENTER ESC FAULT TELEVISION ENCODER OFF the RS-232C terminal on the rear panel. [Configuration Menu] ENTER ESC button button ≠ [Initial Param Menu] ≠ [Control Mode] Operation Fl
ملخص المحتوى في الصفحة رقم 17
Restoring the Default Menu Setting Value Each feature that has been set using the menu can be returned to default (factory setting). All the menu settings return to default. Operation Flow Chart Display Flow Chart Press the ENTER button Main Menu Main Menu screen will be displayed. +Configuration Menu Press the 8 / 9 buttons Main Menu Select the Configuration Menu. +Configuration Menu Press the ENTER button Configuration Menu Configuration Menu screen will be displayed. +Operate Param Menu Press
ملخص المحتوى في الصفحة رقم 18
Starting the Encoding There are 2 ways to start the encoding. One is to start the encoding automatically and the other one is to start it manually by setting the menu. Display 8 / 9 / ; / :buttons POWER POWER ON MULTI FORMAT ENTER ESC HIGH DEFINITION FAULT TELEVISION ENCODER OFF ENTER ESC button button Start the encoding automatically Memo Memo Operation Flow Chart Display Flow Chart The default setting of the Start Mode item is set to Press the ENTER button Initial Param Menu “Auto” in order t
ملخص المحتوى في الصفحة رقم 19
Set the Start Mode item Start the encoding manually in the menu to “Manual” ac- Memo Memo cording to the procedure on Operation Flow Chart Display Flow Chart ☞ Page 18 “Start the The encoding will stop if menu encoding automati- item has been changed dur- cally”. ing manual encoding and Press the ENTER button Main Menu “>Save&Reboot” has been Main Menu screen will be displayed. +Configuration Menu excecuted. Start the encoding manually once again. Press the 8 / 9 buttons Configuration Menu Sel
ملخص المحتوى في الصفحة رقم 20
Checking Operation Status The operation status of this unit can be confirmed from the display. Display 8 / 9 / ; / :buttons POWER POWER ON MULTI FORMAT ENTER ESC HIGH DEFINITION FAULT TELEVISION ENCODER OFF ENTER ESC button button Operation Flow Chart Display Flow Chart Press the ENTER button Main Menu Main Menu screen will be displayed. +Configuration Menu Press the 8 / 9 buttons Main Menu Select the Status Menu. +Status Menu Press the ENTER button Status Menu Status Menu screen will be displa
