ملخص المحتوى في الصفحة رقم 1
Installation and Assembly:
Security Fasteners For Universal PLP Plates
Models: ACC925
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
Parts List
Description Qty. Part Number
A M5 x 12 mm 4 520-1064
B M5 x 25 mm 6 520-1122
I (1)
C M6 x 12 mm 4 520-1050
D M6 x 25 mm 4 520-1211
E M8 x 12 mm 4 520-1724
F M8 x 25 mm 4 520-1101
G M5/M4/M6 washer 4 580-1398
H spacer 4 540-1059
I 4 mm allen wrench 1 560-9646
J M5 x 20 mm
ملخص المحتوى في الصفحة رقم 2
Installing Security Screws for PF and PT wall mount models Replacing Safety/Security Screw NOTE: If installing security screws for SA wall mount models, skip to page 6. 1 Replace safety/security screws with M5 x 25 mm screw (B). Hand thread screw into bottom of flat or tilt adapter bracket as shown in figure 1.1 and 1.2. NOTE: Be sure tip of screw is flush with top of adapter bracket hole. TILT BRACKETS FLAT BRACKETS TOP OF TOP OF ADAPTER ADAPTER BRACKET BRACKET B B fi g 1.1 fi g 1.2 ISSUED: 11
ملخص المحتوى في الصفحة رقم 3
WARNING • Tighten screws so adapter brackets are fi rmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail. To prevent scratching the
ملخص المحتوى في الصفحة رقم 4
For Flat Back Screen Begin with the shortest length screw, hand thread through multi-washer and flat or tilt adapter bracket (not 2-1 included) into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the security fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws. NOTE: Spacers may not be
ملخص المحتوى في الصفحة رقم 5
Installing Adapter Brackets WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the fl at panel screen. • Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque. • Be careful not to pinch fi ngers when pushing screen from the bottom. Hook flat brackets onto wall plate (not included). Then 3 slowly swing screen in as shown in figure 3.1. Using 4 mm security allen wrenc
ملخص المحتوى في الصفحة رقم 6
Installing Security Screws for SA wall mount models WARNING • Tighten screws so screen brackets are fi rmly attached to screen. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may o
ملخص المحتوى في الصفحة رقم 7
For Flat Back Screen Begin with the shortest length screw, hand thread screw through multi-washer and screen brackets (not included) 1-1 into screen as shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the fastener pack. Repeat for remaining mounting holes, level screen brackets and tighten screws. NOTE: Spacers may not be used, dep
ملخص المحتوى في الصفحة رقم 8
® Attaching Adapter Plate to Screen with VESA Mounting Pattern Choose hole pattern as shown in detail 1 for VESA mounting pattern. Begin with the shortest length screw, hand 2 thread through adapter plate into screen as shown in detail 2. Screw must make at least three full turns into the mounting hole and fi t snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the fastener pack. Repeat for remaining mounting holes. Se
ملخص المحتوى في الصفحة رقم 9
WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen. • Failure to lock brake pad with two M5 x 20 mm screws (J) and lock tilt bracket with M5 x 25 mm screw (B) can cause screen to come off mount if hit accidentally. Installing and Removing Flat Panel Screen J To attach screen to arm (not included), insert the puck of BRAKE PAD 3 adapter plate into the tilt bracket slot as shown in fi gure 3.1.
