ملخص المحتوى في الصفحة رقم 1
USFM 100 Installation Guide
The Extron USFM 100 is a mounting kit for suspending ultra short throw projectors from a wall. The USFM 100 base
®
plate enclosure is capable of mounting a PoleVault System switcher and its supplied power supply, with sufficient
room remaining for installing additional devices and cable management. It is designed to be used with the UPB 25
®
universal projector bracket (supplied with the Extron WallVault system).
The USFM 100 has knockouts on all four sides that a
ملخص المحتوى في الصفحة رقم 2
USFM 100 Installation Guide, cont'd Installation WARNING: Before commencing installation, the wall structure must be examined to determine if it is suitable for the proper installation and support of this product. If needed, the installer should reinforce the wall. Drywalls should have a minimum thickness of 1/2 inch and a maximum thickness of 5/8 inch. Improper installation of this product could lead to serious injury. NOTE: Check local building standards and codes to verify that the insta
ملخص المحتوى في الصفحة رقم 3
For drywall with wood studs i. Drill ¼ inch pilot holes at the marked stud locations. ii. Align the base plate mounting holes over the pilot holes and lightly secure with 5/16 inch lag screws and washers. NOTE: If using toggle screws for assembly, follow the installation method (steps A-D) shown in figure 3. D. Hand screw in pan head bolt A. Grasp plastic handle, collapse B. Slide plastic washer down C. Cut off plastic handle close until 1/8 inch gap remains. toggle and insert into
ملخص المحتوى في الصفحة رقم 4
USFM 100 Installation Guide, cont'd 3. Run Cables NOTE: All cable installation should be performed in accordance with local and national building codes, fire and safety codes, and local and national electrical codes. Run signal cables from the PoleVault input wallplates, control device location, and the speakers to the USFM 100 location. Cables can be routed behind the walls, through a surface raceway (such as Wiremold 700 or 2400), or through conduit directly to the USFM 100. 2400 Raceway Op
ملخص المحتوى في الصفحة رقم 5
5. Attach the Boom Arm, Power Supply, and Projector a. Hook the boom arm over the top rail on the base plate so that the tab on the arm (see figure 6, inset) is against the rail. Secure the arm at the bottom with the two supplied (10-32 x 3/8 inch) pan head screws and washers, and at the top with the single ¼-28 x ¾ inch hex screw. Hex Screw Tab Hex Screws and Washers Phillips Pan Head Screws Set Screw Figure 6. Hook Boom Arm Over Rail and Secure b. Secure the power supply within the support
ملخص المحتوى في الصفحة رقم 6
USFM 100 Installation Guide, cont'd 6. Complete the Installation a. Switch on the display device, control device, and signal sources, and configure the system. Adjust the position and length of the boom arm as needed, adjusting the UPB 25 to center the image. When fully satisfied, secure the arm and tighten down all the UPB 25 locking screws. b. Place the covers over the installed plate and boom arm, and secure with supplied screws. Extron USFM 100 Optional Accessory Extron UPB 25 Universal
ملخص المحتوى في الصفحة رقم 7
USFM 100 Dimensions 2.20" 34.40" (5.59 cm) (87.38 cm) 11.14" (28.29 cm) Base Plate (front view) 36.29" (92.19 cm) 2.74" (6.96 cm) 12.94" (32.86 cm) Base Plate with Plastic Covers 31.80" (max.) 31.80" (max.) To Wall (80.77 cm) (80.77 cm) 30.00" (max.) 30.00" (max.) (76.20 cm) (76.20 cm) 21.65" 21.65" (54.99 cm) (54.99 cm) 3.60" 3.60" (9.14 cm) (9.14 cm) Boom Arm (top view) Boom Arm (top view) 12.50" (min.) 12.50" (min.) (31.75 cm) (31.75 cm) 3.85" 3.85" (9.77 cm) (9.77 cm) 31.80" To Wall 31.80" (
ملخص المحتوى في الصفحة رقم 8
USFM 100 Installation Guide, cont'd Aligning the Projector When aligning the projector to the screen or wall display, consult the projector manual for the relevant throw lengths. See the images below for the dimensions of USFM 100 with the UPB 25 installed. Page 6 shows the USFM 100 specifications and page 7 show the basic unit dimensions. 31.80" (max) (80.77 cm) Center of UPB 30.00" (max) 0.0” - 2.0" 31.80" (max (76.20 cm) ) (0 - 5.08 cm) (80.77 cm) Center of UPB 30.00" (max) 0.0” - 2.0" (76.2
