JL Audio Stealthbox 94376 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

SB-F-EDG/10W3v3 INSTR_SKU# 011254
Insa t llat Ion

d I F F I C u l t Y :

If you choose to perform the installation yourself, it is absolutely vital that
®
out
the Stealthbox be properly mounted to the vehicle according to these
o F
instructions. Failure to mount the enclosure properly presents two problems:
I n s t a l l a t I o n G u I d e
for the 1) The sub-bass performance will suffer due to the movement of the enclosure
35
caused by the force exerted by the woofer(s).
SB-F-Edg/

ملخص المحتوى في الصفحة رقم 2

SB-F-EDG/10W3v3_INSTR_SKU# 011254 s t e P 4 S T E P 8 Fold passenger side rear seat forward. Remove passenger side taillight assembly by removing (2) 8mm screws. Remove bolt securing seat belt at lower front of cargo side panel. s t e P 5 S T E P 9 Remove passenger side threshold plate. Carefully pry taillight assembly out, then back, from vehicle, releasing two alignment pins at the front edge. Remove bulbs from assembly by turning 1/4 turn to the left. s t e P 6 S T E P 1 0 Pull pas

ملخص المحتوى في الصفحة رقم 3

SB-F-EDG/10W3v3_INSTR_SKU# 011254 s t e P 1 2 S T E P 1 6 Remove backing from wax square and place it on sheet Put Stealthbox® into final position with mounting stud metal just below tail light wiring as shown. extended through hole drilled in tail light area. Secure with nut, lock washer, and flat washer provided (see illustration). s t e P 1 3 S T E P 1 7 STEALTHBOX WALL Place Stealthbox® into location as shown, push stud against VEHICLE SHEET METAL Position the Stealthbox® into the mou

ملخص المحتوى في الصفحة رقم 4

SB-F-EDG/10W3v3_INSTR_SKU# 011254 s t e P 2 0 S T E P 2 4 Place cargo side panel onto a flat surface with back side up. Drill 1/8 inch holes as indicated on template. Locate back side of storage compartment. Carefully grind heads of plastic spot welds to allow removal of compartment enclosure. Take care not to damage front of panel. s t e P 2 1 S T E P 2 5 Remove storage compartment from side panel. Install grille with short #8 screws and #8 flat washers as provided. s t e P 2 2 S T E P

ملخص المحتوى في الصفحة رقم 5

SB-F-EDG/10W3v3_INSTR_SKU# 011254 I n C l u d e d H a R d W a R e (1) wax square (8) #8x 3/8” Pan head phillips screws (1) 3/8-16 X 2.25 set screw stud (8) #8 SAE Flat Washer (1) 3/8 X 2 fender washer (1) 3/8 lock washer (1) 3/8 X 1.25 nut (1) grill panel template s P e C I F I C a t I o n s Enclosure Type: Acoustic Suspension (sealed) Driver Type: 10W3v3-4 Nominal Impedance: 4 ohms mono Continuous Power Handling: 500 Watts P o W e R R e C o m m e n d a t I o n JL Audio recommends using a