ملخص المحتوى في الصفحة رقم 1
VM1 Video Matrix
HD Component Video Distribution System
Instruction Manual
ملخص المحتوى في الصفحة رقم 2
SAFETY PRECAUTIONS Important Safety Instructions 7. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer. 8. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabin
ملخص المحتوى في الصفحة رقم 3
TABLE OF CONTENTS INTRODUCTION Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Control Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rear-Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INSTALLATION Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Source Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Upconverter Configuration . . . .
ملخص المحتوى في الصفحة رقم 4
INTRODUCTION The 4x4 configurations provide four source inputs and Product Overview four zone outputs. The 8x8 configurations provide The VM1 Video Matrix works with a multiroom audio eight source inputs and eight zone outputs. system to distribute analog component video over a Each source input has red, green, and blue RCA con- single CAT-5e cable to each zone. Capable of han- nectors for component video signals. Each zone out- dling high-definition component video signals, it also put has an R
ملخص المحتوى في الصفحة رقم 5
INTRODUCTION Front (Aux) A/V Input (source 7). This permits the Control Methods Video Matrix to distribute that source instead of run- The Video Matrix is controlled by the system to which ning a separate video cable from the source to the it is connected. It switches video sources to the display and selecting it at the display. zones by receiving source selection commands from The 4x4 configurations of the VM1 respond to source the the host system. selection commands for sources 1 through 4 onl
ملخص المحتوى في الصفحة رقم 6
INSTALLATION Location Upconverter Configuration Locate the VM1 Video Matrix with the host system Models with upconverters are factory set to convert controller and source equipment to facilitate source composite video. Follow the procedure below to set and control connections. Locate the VMR1 Receivers the input switches to S-video or Component as need- near the video displays in the zones, within 300 feet ed before installing the VM1 (see diagram below). (90 m) of the VM1. CAUTION Source Assign
ملخص المحتوى في الصفحة رقم 7
INSTALLATION 3. Connect Receiver cables to VM1. Crimp RJ-45 Rack Mounting connectors on the system end of the CAT-5e cables, To rack mount the VM1, attach the supplied rack following the T568A standard as shown. Plug the ears to the chassis as shown. Leave one rack unit of connectors into the appropriate zone outputs on the space open above and below the VM1 to allow prop- VM1. (If using wall plates, punch down the CAT-5e per er ventilation of the chassis. Do not mount the VM1 the T568A standard
ملخص المحتوى في الصفحة رقم 8
INSTALLATION Typical Application Diagrams RGB cable DVD player* VM1 Video Matrix Audio to controller Power supply CAT-5e cables RJ-45 patch cable SMS3 Smart Media Server VMR1 Receivers Audio to Component video controller distribution amplifier* VGA-component video adapter* Video display* VGA IN CAM6.6T Multiroom Controller RJ-45 patch cable CAM6.6 *Not manufactured by Russound Audio from sources Connection for RNET control by a multiroom audio system 8 RGB cable RGB cables RGB cable VGA serial c
ملخص المحتوى في الصفحة رقم 9
INSTALLATION Connection for RS-232 control by a home automation system 9
ملخص المحتوى في الصفحة رقم 10
REFERENCE Technical Specifications VM1 Video Matrix VM1 8 Component video connectors: 3 RCA per input (RGB) Component video inputs: 8 Zone output connectors: 8-pole modular RJ-45 Zone outputs: 8 System cable: CAT-5e Maximum cable length: 300 ft (90 m) VM1 8UC Video resolution: Up to 1080p Component video inputs: 8 Communication ports: 2 RJ-45 RNET Link S-video inputs: 2 mini-DIN 1 DB9 RS-232 (sources 1 and 4) 1 USB 1.1 Composite video inputs: 2 RCA Power requirement: 24 VDC 2.5 A (sources 1 and
ملخص المحتوى في الصفحة رقم 11
REFERENCE Warranty The Russound VM1 Video Matrix is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. For this warranty to apply, the product must be installed and used according to its written instructions. This warranty does not cover: damage caused by abuse, misuse, negligence, or improper ins
ملخص المحتوى في الصفحة رقم 12
VM1 Video Matrix Component Video Distribution System Instruction Manual Models VM1 4 VM1 4UC VM1 8 VM1 8UC VM1 8UC2 Russound 5 Forbes Road, Newmarket NH 03857 USA Tel 603.659.5170 • Fax 603.659.5388 www.russound.com Technical Support: tech@russound.com 28-1235 03/22/07 Copyright © 2007 Russound. All rights reserved. All trademarks are the property of their respective owners. Specifications are subject to change without notice. Russound is not responsible for typographical errors or omissions.
