ملخص المحتوى في الصفحة رقم 1
704 North Clark Street
Albion
MI 49224 USA
Phone +1 517 629 5990
Fax +1 517 629 5990
www.sepatriot.com
Patriot Antenna Systems
Assembly Manual for the
1.0m Back Pack Antenna
System
1.0 meter Back Pack Antenna
Revision 002
ملخص المحتوى في الصفحة رقم 2
CONTENTS INTRODUCTION ........................................................................................................................................ 2 MECHANICAL SYSTEM DESCRIPTION.............................................................................................. 3 BACK PACK ............................................................................................................................................. 3 AZ-EL ANTENNA BASE ..................................
ملخص المحتوى في الصفحة رقم 3
MECHANICAL SYSTEM DESCRIPTION BACK PACK The antenna is provided in a carrying case measuring approximately 15 x 25 x 12”, and weighs approximately 65 pounds. The back pack case has the added features of having roller wheels and an extendable handle for easy handling where applicable. Back Pack shoulder straps are also provided for carrying the case on one’s back. AZ-EL ANTENNA BASE The Antenna Base is comprised of three detachable legs that have adjustable feet for rough leveling of
ملخص المحتوى في الصفحة رقم 4
4
ملخص المحتوى في الصفحة رقم 5
MOUNT ASSEMBLY The pack has two divided compartments. The topmost compartment has an access flap that is easily opened with its’ perimeter zipper. Open this flap and you will find the Mount Assembly parts needed for this stage of the assembly. 1. Slide the Feet assemblies into each of the 3 Leg assemblies as shown. The flatted side of the pin faces the locking cam. Simply turn the cam downward to lock the pin at the desired height. 2. Insert the Leg assemblies onto the bottom side of
ملخص المحتوى في الصفحة رقم 6
REFLECTOR ASSEMBLY Two of the reflector panels are in the topmost compartment, and the remaining four as well as the feed support parts are in the bottom compartment which can be accessed with the perimeter zipper around the middle of the case. Remove them taking note how they were packed so they can be repacked accordingly. You will need the bottom-most panel to begin with. 1. Starting with panel B2, guide the mounting lugs into the receiving brackets of the Mount assembly taking car
ملخص المحتوى في الصفحة رقم 7
3. Install panel T2 by simply guiding it into position as shown onto the alignment dowels. The panel will stay in place. The seam between the panels should look flush. 7
ملخص المحتوى في الصفحة رقم 8
4. Install panel T1 and B3 using the same procedure as in step 3. 8
ملخص المحتوى في الصفحة رقم 9
5. Install panel B1 and B3 using the same procedure as in step 3. Panels B1 and B3 will need to be held slightly back and aligned simultaneously with their respective upper panel and it’s alignment dowel. 9
ملخص المحتوى في الصفحة رقم 10
After making sure all seams look flush fasten the two latches on the back of the dish, then fasten the six remaining perimeter latches. 10
ملخص المحتوى في الصفحة رقم 11
FEED ASSEMBLY 1. With all latches securely latched readjust Elevation Angle to facilitate attachment of the Feed Assembly parts. (Appox. 45deg) 2. Insert the Feed Tube assembly into the receiver at the bottom of panel B2. It must be held at the approximate angle shown. Then once it is fully inserted, rotate upwards to be able to attach the side struts. 11
ملخص المحتوى في الصفحة رقم 12
3. Attach each side strut. Snap on to side panels first then snap to corresponding ball snap on the Feed Tube assembly. Assembly is now complete. Antenna system can acquire satellite once RF connections are complete. 12
