ملخص المحتوى في الصفحة رقم 1
Professional Disc Jockey Products
PRO TT-2
PROFESSIONAL DIRECT DRIVE TURNTABLE
OWNER’S MANUAL
©2000 Industries http://www.numark.com
ملخص المحتوى في الصفحة رقم 2
PRO TT-2 Turntable 8. Power Sources - This product should be connected to a Safety Information power supply only of the type described in these operating instructions, or as marked on the unit. 9. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord. 10. Object and Liquid
ملخص المحتوى في الصفحة رقم 3
PRO TT-2 Turntable IMPORTANT INFORMATION... GENERAL SYSTEM PRECAUTIONS Please read this entire manual before connecting the unit to your system. • Use appropriate cables throughout your system: Quality shielded audio cables and terminated shielded video cables, low-capacitance preferred. Speaker cables must be For optimum performance: 14-gauge minimum; 12- or 10-gauge is better. 1. Always make sure that AC power is OFF while making • Be sure plugs and jacks are tightly mated. Loose any connecti
ملخص المحتوى في الصفحة رقم 4
PRO TT-2 Turntable PRO TT-2 PROFESSIONAL DIRECT-DRIVE TURNTABLE CONGRATULATIONS! You are now the owner a PRO TT-2 Professional Turntable, the ultimate tool for today’s skilled turntablist. This unit has been designed by DJs for DJs. With its super high-torque platter and large back lit display the PRO TT-2 gives the professional absolute total control. Enjoy this turntable and remember: BE CREATIVE! Thank you for buying Numark DJ products! FEATURES: • ± 10 or20% p
ملخص المحتوى في الصفحة رقم 5
PRO TT-2 Turntable TABLE OF CONTENTS Safety Information Page 2 Introduction Page 4 Product Registration Page 5 Diagram and Parts Description Page 6 Operating Instructions Page 10 Specifications Page 11 Warranty and Service Page 12 Contents of this package • Main Unit 1 • Turntable platter 1 • Turntable slip mat 1 • Dust cover 1 • Dust cover clips 2 • 45-rpm adapter 1 • Counterweight 1 • Headshell 1 Product Registration Please record the serial number of your unit as shown on the chassis, under
ملخص المحتوى في الصفحة رقم 6
PRO TT-2 Turntable DIAGRAM AND PARTS DESCRIPTION 9 10 8 11 7 12 6 13 5 14 4 15 17 1 16 2 3 To fully appreciate the features of the PRO TT-2, please read this entire manual before you begin operation. The PRO TT-2 should be placed on a level sturdy surface. Keep in mind that there are a few features you may never have seen before on a turntable of this type that you will need to read about to use properly. Start by removing all parts from the package and place on a level surface. Carefully ch
ملخص المحتوى في الصفحة رقم 7
PRO TT-2 Turntable 19. Headshell Locking Nut - Attach headshell by TONE ARM ASSEMBLY inserting into the front end of the tonearm, then turn the locking nut clockwise with the head shell firmly held horizontally. 28 27 26 20. S-Shaped Tone Arm 25 22 21. Tone Arm Clamp and Rest - Use this rest for the tone arm and clamp it in position during 24 23 transportation. 22. Tone Arm Lift - This elevates the tone arm 21 above the record surface. 23. Tone Arm Lift Adjust Screw - Controls the amount of lif
ملخص المحتوى في الصفحة رقم 8
PRO TT-2 Turntable TONE ARM SETTINGS LCD DISPLAY The following explains proper counterweight and 32 anti-skating set up. Cartridge manufacturers usually specify the proper settings. 31 33 a) Remove the stylus protector, do not touch the stylus tip during the adjustment. b) Set the cueing lever to the lower position so it does not effect tone arm height. 29 c) Set Anti-skate adjustment to 0. 30 d) Place counterweight on the rear of the tone arm e) Release the arm clamp and lift the tonearm from
ملخص المحتوى في الصفحة رقم 9
PRO TT-2 Turntable REAR PANEL DIAGRAM 34 35 39 40 37 36 38 41 34. Removable Lid - Protects the turntable from dirt and dust. 35. Hinge Assembly - Holds the lid and turntable together. Attach now by sliding the bottom tabs of the Hinge Assembly into the Hinge Holders. 36. Platter Speed Output - This output is to be used with external devices that require platter speed information. 37. Remote Start/Stop - This is used with external control devices. Tech note: This circuit is normally open. Use a
ملخص المحتوى في الصفحة رقم 10
PRO TT-2 Turntable GENERAL OPERATING INSTRUCTIONS 1. Turn the power dial to turn on and the speed indicator and the strobe-illuminator will light up. 2. Turn on and raise the target light for illuminating the stylus tip by pushing the target light button. 3. Place a record on the turntable mat. When playing a 45rpm record with a large center hole; place the 45- rpm adapter on the center spindle. 4. Set the rotation speed (33/45/78) to match the record. 5. Release the arm clamp. 6. Set the cue
ملخص المحتوى في الصفحة رقم 11
PRO TT-2 Turntable SPECIFICATIONS TURNTABLE SECTION Type 3-speed, full manual Driving method Direct drive Motor 12 Pole, 3 Phase, Brushless DC Motor Turntable platter Aluminum diecast 330mm dia. Turntable speed 33-l/3 , 45, and 78 rpm Pitch Variance ±20% Starting Torque more than 2.2kgf.cm Braking Electronic OUTPUT Wow and flutter < 0.13% S/N ratio > 55dB (DIN-B) Output Difference 2.3dB Channel Separation 16dB Pitch 675±1Hz with 33 1/3 rpm 1170±1Hz with 78 rpm TONEARM SECTION Typ
ملخص المحتوى في الصفحة رقم 12
Professional Disc Jockey Products LIMITED PRODUCT WARRANTY What is covered and for how long? 1. NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK'S DJ mixers and amplifiers are free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer and continuing for the following period of time after that date for (2) Years. The warranty is extended to (3) Years with the comple
