ملخص المحتوى في الصفحة رقم 1
C
B
A
STO OP P
C
B
A
S ST TO OP P
C
B
A
S ST TO OP P
Trim ‘n Edge model
UT20022, UT20022A,
UT20023, UT20023A
OPERATOR'S MANUAL
25cc String Trimmers
Trimlite model
UT20002, UT20002A,
UT20003, UT20003A
Easy Reach model
UT20042, UT20042A,
UT20043, UT20043A
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS ■■■■■ Introduction ................................................................................................................................................................. 2 ■■■■■ General Safety Rules .................................................................................................................................................. 3 ■■■■■ Specific Safety Rules ...............................................................................................
ملخص المحتوى في الصفحة رقم 3
GENERAL SAFETY RULES ■■■■■ Do not touch area around the muffler or cylinder of the unit, these parts get hot from operation. WARNING: ■■■■■ Always stop the engine and remove the spark plug wire before making any adjustments or repairs except Read and understand all instructions. Failure to follow for carburetor adjustments. all instructions listed below may result in electric shock, fire and/or serious personal injury. ■■■■■ Inspect the unit before each use for loose fasteners, fuel leaks, etc
ملخص المحتوى في الصفحة رقم 4
SPECIFIC SAFETY RULES ■■■■■ Use only the manufacturer's replacement string in the SPECIFIC SAFETY RULES FOR TRIMMER cutting head. Do not use any other cutting attachment. USE To install any other brand of cutting head to this string ■■■■■ Replace string head if cracked, chipped, or damaged in trimmer can result in serious personal injury. any way. Be sure the string head or blade is properly ■■■■■ Never operate unit without the grass deflector in place installed and securely fastened. Failure to
ملخص المحتوى في الصفحة رقم 5
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning for safe operation of this product. SYMBOL NAME EXPLANATION Safety Alert Symbol Precautions that involve your safety. . Read the Operator’s Manual To reduce the risk of injury, user must read and understand operator’s manual before using this product. Wear Eye and Hearing Protection Wear eye protection which is marked to comply with ANSI Z87.1 as well as hearing protection when operating thi
ملخص المحتوى في الصفحة رقم 6
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. CAUTION:
ملخص المحتوى في الصفحة رقم 7
SPECIFICATIONS Weight - (without fuel) Trimlite (UT20002, UT20002A, UT20003, UT20003A) .......................................................................... 9.6 lbs. (4.4 kg.) Trim ‘n Edge (UT20022, UT20022A, UT20023, UT20023A) ................................................................... 10 lbs. (4.5 kg.) Easy Reach (UT20042, UT20042A, UT20043, UT20043A) ................................................................. 10.6 lbs. (4.8 kg.) String cutting width ........................
ملخص المحتوى في الصفحة رقم 8
C B A S ST TO OP P FEATURES FEATURES Trimlite model PRIMER BULB UT20002, UT20002A, UT20003, UT20003A STARTER GRIP CHOKE LEVER FRONT HANDLE STOP BUTTON REAR HANDLE DRIVE SHAFT HOUSING THROTTLE TRIGGER CURVED SHAFT GRASS DEFLECTOR STRING HEAD Fig. 1a Page 8
ملخص المحتوى في الصفحة رقم 9
C B A S ST TO OP P C B A S ST TO OP P FEATURES PRIMER BULB Trim ‘n Edge model UT20022, UT20022A, UT20023, UT20023A STARTER GRIP CHOKE LEVER STOP BUTTON FRONT HANDLE REAR HANDLE DRIVE SHAFT THROTTLE TRIGGER HOUSING CURVED SHAFT GRASS DEFLECTOR EDGER ATTACHMENT (TRIM ‘N EDGE ONLY) STRING HEAD Fig. 1b Easy Reach models PRIMER BULB UT20042, UT
ملخص المحتوى في الصفحة رقم 10
ASSEMBLY If your unit has been preassembled, check each step to make sure the unit has been properly assembled. FRONT HANDLE FRONT HANDLE See Figure 2. 1. Remove the front handle, bolt, and wing nut from the WING NUT Owner’s Kit. 2. Install the front handle onto the top side of the drive BOLT shaft housing and move it to a comfortable position. 3. Place the bolt through the front handle as shown
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY CURVED SHAFT GRASS DEFLECTOR WITH EDGER GUIDE - TRIM ‘N EDGE ONLY See Figures 5 and 6. 1. Remove the wing nut, flat washer, lock washer, and bolt from the Owner’s Kit. 2. Place the curved shaft grass deflector over the shaft and bracket. 3. Slide the assembled edger guide over the tabs on the grass deflector and bracket. 4. Place the bolt through the slots in the tabs on the grass deflector and
ملخص المحتوى في الصفحة رقم 12
OPERATION FUELING AND REFUELING THE TRIMMER OPERATING THE TRIMMER See Figure 8. FUEL MIXTURE This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil. Pre-mix unleaded WARNING: gasoline and 2-cycle engine oil in a clean 1 gallon con- Always position the unit on the operator's right side. tainer approved for gasoline. The use of the unit on the operator's left side will expose Recommended fuel: This engine is certified to operate on the user to hot surfaces
ملخص المحتوى في الصفحة رقم 13
OPERATION ADVANCING THE STRING TRIMLITE AND TRIM ‘N EDGE ADVANCING STRING USING THE EZ LINE™ TAP DANGEROUS ADVANCE SYSTEM CUTTING AREA String advance is controlled by tapping string head on grass while running engine at full throttle. 1. Run engine at full throttle. 2. Tap string head on ground to advance string. String advances each time the head is tapped. 3. Several taps may be required until string strikes the cut DIRECTION OF of
ملخص المحتوى في الصفحة رقم 14
OPERATION EDGER GUIDE OPERATION - TRIM ‘N EDGE ONLY See Figures 10 and 11. WING NUT ■ Loosen the wing nut and slide the edger guide to adjust it to the desired trimming length then retighten the wing nut securely. Refer to “Edger Guide Assembly” earlier in this manual for additional information. ■ The edger guide allows the trimmer to be used as an edger for cutting along sidewalks, driveways, flower beds, etc. The edger guide is convenient to use and supports the trimmer as it is being used as
ملخص المحتوى في الصفحة رقم 15
C B A S ST TOP OP C B A S ST TO OP P OPERATION STARTING AND STOPPING PRIMER BULB See Figures 12 and 13. Trimmer should be on a flat, bare surface for starting. 1. Slowly press the primer bulb seven (7) times. 2. Set the choke lever to the FULL CHOKE position (A). 3. Squeeze the throttle trigger fully and pull starter handle sharply until engine attempts to run. Do not pull the starter handle more than eight (8) times. NOTE: Keep throttle trigger squeezed fully through STEP 6. 4. Set the choke le
ملخص المحتوى في الصفحة رقم 16
MAINTENANCE WARNING: Use only original manufacturer's replacement parts, accessories and attachments. Failure to do so can cause poor performance, possible injury and may void your warranty. You can often make adjustments and repairs described here. For other repairs, have the trimmer serviced by an SPOOL RETAINER Fig. 14 authorized service dealer. SPOOL REPLACEMENT EZ LINE™ TAP ADVANCE SYSTEM SPRING NEW PREWOUND SPOOL See Figures 14 and 15. SLOTS If replacing string only, refer to “String Rep
ملخص المحتوى في الصفحة رقم 17
MAINTENANCE STRING REPLACEMENT SPOOL See Figures 16, 17, 18 and 19. SPRING 1. Stop the engine, disconnect the spark plug wire. Hold the string head and unscrew the spool retainer. ARROWS ON To remove the spool retainer: SPOOL Turn the spool retainer counterclockwise for Trimlite and Trim n’ Edge. Turn the spool retainer clockwise for Easy Reach. ANCHOR 2. Remove the spool from the string head. NOTE: Keep HOLE the spring attached to the spool. Remove any old string remaining on the spool. FIRST
ملخص المحتوى في الصفحة رقم 18
C B A STOP 3 2 1 STO OP P C B A STOP MAINTENANCE Spark Arrestor Cleaning Instructions: LATCH ■■ ■■■ Remove the spark arrestor from the muffler. ■■ ■■■ If your spark arrestor is made of a fiberglass material, discard and replace. ■■ ■■■ If your spark arrestor is made of a metal material follow these cleaning instructions: 1. Spray the spark arrestor with a quality carbon cleaner. 2. Gently clean using a wire brush. 3. Install the new or cleaned spark arrestor and PULL COVER reassemble completely
ملخص المحتوى في الصفحة رقم 19
TROUBLESHOOTING IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER. PROBLEM POSSIBLE CAUSE SOLUTION Engine will not start: 1. No spark. 1. Check spark. Remove spark plug. Reattach the spark plug cap and lay spark plug on metal cylinder. Pull the starter rope and watch for spark at spark plug tip. If there is no spark, repeat test with a new spark plug. 2. No fuel. 2. Push primer bulb until bulb is full of fuel. If bulb does not fill, primary fuel delivery system i
ملخص المحتوى في الصفحة رقم 20
C B A STO OP P TROUBLESHOOTING IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER. PROBLEM POSSIBLE CAUSE SOLUTION String will not advance 1. String is welded to itself. 1. Lubricate with silicone spray. when using 2. Not enough string on spool. 2. Install more string. Refer to “String Replace- the EZ Line™ tap advance ment” earlier in this manual. system: 3. String is worn too short. 3. Pull strings while alternately pressing down on and releasing spool retainer.
