ملخص المحتوى في الصفحة رقم 1
Grass Trimmer
Operator's Manual
MODELS GT-2000
Serial Number 001001 & Up Occasional Use
GT-2000 Type 1E
Serial Number 001001 & Up Occasional Use
GT-2400
Serial Number 001001 & Up Commercial Use
GT-2400 Type 1E
Serial Number 001001 & Up Commercial Use
WARNING DANGER
Read rules for safe operation and instructions carefully. ECHO provides an
Operator's Manual and a Safety Manual. Both must be read and understood for
proper and safe operation.
89869547933
X7532271503
02/01
ملخص المحتوى في الصفحة رقم 2
2 INTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the- job-dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operations tips and SAFETY messages. WARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual. Both must be read and understood for proper and
ملخص المحتوى في الصفحة رقم 3
GRASS TRIMMER 3 OPERATOR'S MANUAL MANUALSAFETY SYMBOLS AND IMPORTANT INFORMATION Throughout this manual and on the product itself, you will find safety alerts and helpful, information messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you. This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and IMPORTANT The enclosed message
ملخص المحتوى في الصفحة رقم 4
4 INTERNATIONAL SYMBOLS SYMBOL SYMBOL FORM/ SYMBOL SYMBOL SYMBOL SYMBOL FORM/ SYMBOL FORM/ SYMBOL FORM/ DESCRIPTION/APPLICATION DESCRIPTION/APPLICATION DESCRIPTION/APPLICATION SHAPE DESCRIPTION/APPLICATION SHAPE SHAPE SHAPE DO NOT ALLOW Read and understand FUEL AND OIL FLAMES OR Operator's Manual. EMERGENCY STOP MIXTURE SPARKS NEAR FUEL. WEAR EYES, EARS IGNITION Engine choke FINGER SEVERING AND HEAD control. ON/OFF PROTECTION WEAR SLIP HOT CARBURETOR PRIMER RESISTANT SURFACE ADJUSTMENT FOOT WEAR
ملخص المحتوى في الصفحة رقم 5
GRASS TRIMMER 5 OPERATOR'S MANUAL Spark Arrestor - Catalytic Muffler/Muffler The muffler or catalytic muffler controls the exhaust noise and emissions. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Make sure the spark arrestor screen is in good repair and properly seated in the muffler. Keep exhaust area clear of flammable debris. Avoid contact during and immediately after operation. FUEL WARNING DANGER Fuel is VERY flammable. Use extreme ca
ملخص المحتوى في الصفحة رقم 6
6 PERSONAL CONDITION AND SAFETY EQUIPMENT WARNING DANGER Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a trimmer. Physical Condition -- Your judgment and physical dexterity may not be good: if you are tired or sick, if you are taking medication, if you have taken alcohol or drugs. Operate unit only if you are physically
ملخص المحتوى في الصفحة رقم 7
GRASS TRIMMER 7 OPERATOR'S MANUAL SAFE OPERATION Determine Operation Area Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. 15 m (50 ft.) Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions. Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15 m (50 ft.) while the trimmer is in use. Operation Use Proper Clothing & Equipment Before starting th
ملخص المحتوى في الصفحة رقم 8
8 EXTENDED OPERATION/EXTREME CONDITIONS Vibration and Cold -- It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers. The following precautions are strongly recommended because the minimum exposure which might trigger the ailment is unknown. Keep your body war
ملخص المحتوى في الصفحة رقم 9
GRASS TRIMMER 9 OPERATOR'S MANUAL DESCRIPTION The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and positioning of the front handle are necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. IMPORTANT ENGINE INFORMATION EMISSION CONTROL -- ENGINE FAMILY : TEH021UB24RA DISPLACEMENT :
ملخص المحتوى في الصفحة رقم 10
10 1. OPERATOR'S MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference, i.e., operation, maintenance, storage and specifications. 2. SAFETY MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference to learn proper, safe operating techniques. 3. POWER HEAD - Factory Assembled to the Driveshaft assembly. Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 4. FR
ملخص المحتوى في الصفحة رقم 11
GRASS TRIMMER 11 OPERATOR'S MANUAL SPECIFICATIONS M0 ODEL G0 T-200 GT-240 L) ength 1) 400 mm (55.1 in. 1500 mm (59.1 in. Width 330 mm (13.0 in.) Height 360 mm (14.2 in.) W) eight (dry) w/Cutter Head4) .2 kg (9.3 lb. 4.5 kg (9.9 lb. Engine Type Air cooled, two-stroke, single cylinder gasoline engine B) ore 3) 2.2 mm (1.268 in. 34.0 mm (1.34 in. Stroke 26.0 mm (1.04 in.) D) isplacement 2) 1.2 cc (1.29 cu. in. 23.6 cc (1.44 cu. in Exhaust System Spark Arrestor Muffler Carburetor Zama diaphragm mode
ملخص المحتوى في الصفحة رقم 12
12 ASSEMBLY Tools Required: Locking Tool PLASTIC SHIELD 1. Snap the shield over the bearing housing. 2. Install bolt (A), washer (B) and wing nut (C). NYLON LINE HEAD 1. Align locating hole in locating plate with hole in bearing housing. 2. Insert 1/8" dia. locking tool (D) (not included with unit) and thread cutting attachment onto shaft clockwise until head is tight. IMPORTANT Remember to remove the locking tool. FRONT (LOOP) HANDLE NOTE Front handle is pre-installed. Re-positioning and tighte
ملخص المحتوى في الصفحة رقم 13
GRASS TRIMMER 13 OPERATOR'S MANUAL PRE - OPERATION FUEL Fuel Requirements R + M Gasoline - Use 89 Octane [ ] (mid grade or higher) gasoline known 2 to be good quality. Gasoline may contain up to 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is NOT approved. Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD Standard (ISO/CD 13738), must be used. Echo brand Premium 50:1 oil meets this standard. Engine problems due to inadequate lubrication caused
ملخص المحتوى في الصفحة رقم 14
14 IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your ECHO dealer for ordering information. After refueling; Wipe any spilled fuel from the unit. Move at least 3 m (10 ft.) from refueling location before starting the engine. After use; DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container. Storage - Fuel
ملخص المحتوى في الصفحة رقم 15
GRASS TRIMMER 15 OPERATOR'S MANUAL Check that front (loop) handle and shoulder strap/ or shoulder/waist harness are adjusted for safe, comfortable operation. See Assembly for proper adjustment. Have repairs done only by an authorized ECHO Service Dealer. Do not use any attachment, accessory or replacement part unless it is recommended in the Operator's Manual. DETERMINE OPERATION AREA Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions. 15 m (50 ft.
ملخص المحتوى في الصفحة رقم 16
16 STARTING COLD ENGINE WARNING DANGER The cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result. 1. Stop Switch - Start/Run. Move stop switch button (A) away from the STOP position. 2. Choke Lever - Cold Start. Move choke (B) to “Cold Start” Position. 3. Primer - Pump Bulb Pump primer bulb (C) until fuel will be visible and
ملخص المحتوى في الصفحة رقم 17
GRASS TRIMMER 17 OPERATOR'S MANUAL STARTING WARM ENGINE WARNING DANGER The cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result. 1. Stop Switch - Start/Run. Move stop switch button (A) away from the STOP position. 2. Start - Pull Rope. Lay the trimmer on a flat clear area and pull the starter handle (D) until the engine f
ملخص المحتوى في الصفحة رقم 18
18 MAINTENANCE WARNING DANGER Do not perform maintenance on engine or muffler until engine and muffler are completely cool, otherwise serious personal injury may result. Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you wa
ملخص المحتوى في الصفحة رقم 19
GRASS TRIMMER 19 OPERATOR'S MANUAL AIR FILTER Level 1. Tools required: Cleaning brush, 25 or 50 mm (1 or 2 in.) medium bristle paint brush. TM Parts required: 90008 REPOWER AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumu- lated dirt from the air cleaner area. 2. Remove the air cleaner cover. Clean and inspect the element for damage. If element is fuel soaked and very dirty, replace.
ملخص المحتوى في الصفحة رقم 20
20 SPARK PLUG Level 2. Tools Required: Spark Plug socket wrench and screw driver, Feeler gauge, preferably a wire gauge. TM Parts Required: 90064 REPOWER TUNE-UP KIT 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 3. Adjust spark plug gap by bending outer electrode. 4. Tighten spark plug to 145-155 kg/cm (125-135 in. lb.). 0.65 mm (0.026 in.) COOLING SYSTE
