Winegard MA1055W دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

®
WINEGARD
®
MOTORIZED SENSAR ANTENNA
Models MA1055W & MA1055G
MADE IN U.S.A.
U.S. Patents D500,496 and 7,358,909
INSTALLATION MANUAL
CAUTION: This system is not for use with antenna in raised position
while vehicle is in motion.
OEM Model MA1055W has white antenna head and white turret.
OEM Model MA1055G has gray antenna head and black turret.
Unit packed as follows:
Motorized Mount with booms attached.
Antenna Head
Hardware Bag
Instructions
Power Cable (Sold separately, CL-MA03)
Control Cable

ملخص المحتوى في الصفحة رقم 2

Tools Needed/Specifications Tools needed for installation Tape measure 7/16" wrench Cutter 5/16" socket/nut driver Phillips screwdriver 1-1/2" to 3" hole saw (cable entry hole) Electric or cordless drill Sealant compatible with roof material (check with your vehicle manufacturer for compatibility) 1/8" drill bit (for pilot holes) System Specs for Motorized Sensar Electronic Specifications: Operating Voltage Nominal 12VDC - Operating range 9.5 VDC to 15.5 VDC Current draw of electronics when Powe

ملخص المحتوى في الصفحة رقم 3

FRONT OF RV Pre-Installation Requirements To install the Winegard Motorized Sensar antenna, check with your RV dealer or manufacturer. Your RV may already be pre-wired for this system, and/or may have a reinforced Roof Edge FIGURE 3 roof area available. 10 inches STEP 1: Choose location for antenna system on roof area. Min. Figure 3 illustrates placement of system, showing it in travel position. You must be able to raise and rotate antenna without interfering with other roof-mounted equipment

ملخص المحتوى في الصفحة رقم 4

Coax Connector Roof Installation STEP 1: Attach antenna head to booms shown in Figure 2 STEP 3: In traced triangular area for cables, drill a hole (1.5" using two pins and E-Clips found in hardware package. to 3" Dia.) in roof. Route cables through roof to where you have Fasten coax to antenna head. See Figure 2B.Tighten coax selected control panel to be mounted. See Figure 4. connection per instruction decal on antenna head. FIGURE 4 Drill hole 1-1/2" to 3" Diameter for Wires on Roof Leveling

ملخص المحتوى في الصفحة رقم 5

Inside Installation Control Panel Installation STEP 1: Run control cable from roof mount to control panel. STEP 4: Control panel can be mounted directly to surface Do not connect to control panel at this time. providing surface has sufficient space behind panel for wiring. Should you be limited to space behind panel or choose not to STEP 2: Connect power cable to a fused 12VDC source. It is have wires concealed behind control panel, you can use the recommended that the power source is separate

ملخص المحتوى في الصفحة رقم 6

Warranty Returned units damaged in shipping due to improper packing will be charged to the dealer/customer. WINEGARD MOBILE PRODUCTS LIMITED WARRANTY (2 YEARS PARTS; 1 YEAR LABOR) Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products. No w

ملخص المحتوى في الصفحة رقم 7

Notes 7

ملخص المحتوى في الصفحة رقم 8

Printed in U.S.A. Winegard Company • 3000 Kirkwood Street � Burlington, Iowa 52601-2000 © Winegard Company, 2006 2452068 Rev.3 8/10 8