Lucent Technologies 6220 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

6218 and 6220 Telephones
Quick Reference
Document Ordering No. 555-230-713
Comcode 108504333
Issue 2, August 1999

ملخص المحتوى في الصفحة رقم 2

IMPORTANT INFORMATION SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS When you see this warning symbol on the The most careful attention has been devoted to quality standards product, refer to these instructions packed with in the manufacture of your new telephone. Safety is a major ! the product for more information before factor in the design of every set, but, safety is YOUR proceeding further in the installation process. responsibility too. Please read carefully the helpful tips listed bel

ملخص المحتوى في الصفحة رقم 3

THE 6218 and 6220 TELEPHONES 6218 6220 DATA Personalized Personalized DATA jack Ring Ring jack Handset Parking Handset Ringer volume Tab Parking control Ringer Tab volume control Handset 10 Handset 10 Programmable Program Programmable 6218 Dialing buttons Program Dialing buttons button 6220 button Program Pause Pause button Tel.# Program Pause Mute button Pause button Handset Tel.# Handset cord jack Message light cord jack Message light Handset Mute Spkr Speakerphone Handset/ volume ABC DEF Sp

ملخص المحتوى في الصفحة رقم 4

6. Turn the telephone right-side up and place it on your —— INSTALLATION —— desk or table. 7. Plug one end of the coiled handset cord into the handset TABLE/DESK INSTALLATION jack on the side of the telephone. 8. Plug the other end of the handset cord into the handset. Use the 14-foot straight line cord that came with your 9. Hang up the handset. telephone to connect the telephone to a modular jack. 10. Plug the free end of the line cord into a modular wall ! jack. WARNING: Do not plug t

ملخص المحتوى في الصفحة رقم 5

7. Plug one end of the coiled handset cord into the handset MUTE (available only on the 6220 telephone) jack on the side of the telephone. To prevent the other party from hearing you 8. Plug the free end of the line cord into a modular wall (To mute the microphone) jack. Press . Mute 9. Place the telephone against the wall jack mount and push down so that the base locks into the slots on the • Red light next to Mute goes on, and the other party telephone. cannot hear you. 10. Plug the fre

ملخص المحتوى في الصفحة رقم 6

To label and reinstall the programmable dialing REDIAL buttons designation card on your telephone 1. Remove the plastic card cover from the telephone by To redial the last number that you dialed placing your fingers at the top and bottom and flexing 1. While off-hook, press Redial . the card outward. Then, lift the button designation card • The telephone will redial up to 24 digits. from out of its cavity on the telephone. 2. In the blank space next to the appropriate SPEAKERPHONE (availa

ملخص المحتوى في الصفحة رقم 7

To program Hold for normal Hold (that is, the REPAIR INSTRUCTIONS feature which allows the user to put a call on hold) If it is determined that your telephone is malfunctioning, the 1. Press the Program button; then press Flash ; FCC requires that it not be used and that it be unplugged from then press Hold . the modular outlet until the problem is corrected. Repairs can only be made by the manufacturer or its authorized agents or 2. Press Hold again; then press Flash again; by others who m

ملخص المحتوى في الصفحة رقم 8

Prepared by BCS Product Publications Lucent Technologies Copyright © 1999 Middletown, NJ 07748-9972 Lucent Technologies