ملخص المحتوى في الصفحة رقم 1
13 MEMORY CALLER ID TRIM PHONE
MODEL PH-543
OPERATING INSTRUCTIONS
CALLER ID SHOWS YOU CALLERS NAME & NUMBER
70 NAME & NUMBER CALLER ID MEMORY
TONE/PULSE SWITCHABLE DIALING
AUTOMATIC TIME & DATE DISPLAY
ONE-TOUCH CALLER ID CALL BACK
3 ONE-TOUCH SPEED DIAL BUTTONS
10 TWO-TOUCH SPEED DIAL MEMORY LOCATIONS
WALL/DESK USABLE
USES 3 SIZE AA BATTERIES (NOT INCLUDED)
TO USE THIS CALLER ID FEATURES OF THIS PHONE,
YOU MUST SUBSCRIBE TO CALLER ID SERVICE,
AND REMEMBER TO INSTALL BATTER
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS a aaaaaaa Important Safety Instructions 1 a aaaaaaaaa Battery Safety Instructions 2 aaaaaaaaaaaaa a FCC Information 3 aaaa aaaaaaaa Location of Controls 4 Getting Started Step 1: Checking the Package Contents 5 aaaaa a Step 2: Telephone Installation 6 a aaaa Step 3: Setting up the Telephone 7 aaaaaa Adjust the LCD Contrast Level 8 Basics a a a aaaa Making and Receiving Calls 8 aaaa Volume Control and Ringer Setting 8 Last Number Redialing / Pause & Flash aaaaaaaaaaaaaaaa F
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following: 1.Read and follow all instructions and warnings. 2.Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a slightly dampened cloth only. 3.Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or
ملخص المحتوى في الصفحة رقم 4
BATTERY SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY, READ AND FOLLOW THESE INSTRUCTIONS. 1. Use only the following type and size of batteries: 3 size AA alkaline batteries (not included). 2. Do not dispose the batteries into a fire. The cells may explode. Check with local codes for possible special disposal instructions. 3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swal
ملخص المحتوى في الصفحة رقم 5
FCC INFORMATION FCC REGISTRATION This telephone set is registered with the FCC based upon compliance with Part 68 of its rules. Connection of this telephone to the nationwide telecommunications network must be through a standard network jack (RJ11W or RJ11C) which you can order from your telephone company, if not already installed. NOTE: FCC registration does not constitute an expressed or implied guarantee of performance. Only the Limited Warranty in this booklet covers the performance of this
ملخص المحتوى في الصفحة رقم 6
LOCATION OF CONTROLS 5 4 9 10 3 11 6 2 12 7 1 13 14 15 16 8 17 19 18 1. FLASH BUTTON 2. MUTE BUTTON 3. STORE (MEMORY) BUTTON 4. ONE-TOUCH SPEED DIAL BUTTONS (M1, M2 & M3) 5. HOOK SWITCH 6. AUTO (MEMORY) BUTTON 7. REDIAL/PAUSE BUTTON 8. COILED CORD JACK 9. LINE CORD JACK (on bottom) 10. RINGER (HIGH/LOW/OFF) SWITCH 11. BATTERY COMPARTMENT 12. TELEPHONE NUMBER INDEX 13. NEW CALL INDICATOR 14. CALLER ID DISPLAY 15. UP & DOWN BUTTONS 16. DELETE BUTTON 17. CALLBACK/ADJUST BUTTON 18.
ملخص المحتوى في الصفحة رقم 7
GETTING STARTED Step 1: Checking the Package Contents Your new PH-543 Caller ID Trim Phone has all the features of a 13 memory telephone plus Caller ID display. As you unpack this set, make sure you have the following items in the package. HANDSET TELEPHONE BASE COILED HANDSET CORD STRAIGHT TELEPHONE LINE CORD SHORT STRAIGHT WALL CORD (for Wall Mounting use) 5 IB-PH543(168F)-WM-E-051203
ملخص المحتوى في الصفحة رقم 8
GETTING STARTED Step 2: Telephone Installation INSTALLING BATTERIES Before you connect the phone cords, follow these steps to install the batteries: 1. Push down the battery door tab with a pen or other pointed object and lift the battery door out (Fig. 1). 2. Insert 3 size AA alkaline batteries as shown inside the battery compartment (Fig. 2). (The negative side () of the battery touches the battery spring.) 3. Replace the battery door and snap it shut (Fig. 3). Fig. 1 Fig. 2 Fig. 3 CAUTION
ملخص المحتوى في الصفحة رقم 9
GETTING STARTED Step 3: Setting up the telephone SETTING UP LCD CONTRAST, LANGUAGE, AREA CODE, TIME & DATE, AND TONE OR PULSE MODE You may need to set up the LCD contrast, language, area code, time and date, and tone or pulse mode for your telephone when you install the batteries for the first time or when you move to an area that has a different area code. This is necessary because the phone must distinguish local or long distance calls to properly dial calls from the Caller ID list. NOTE: Duri
ملخص المحتوى في الصفحة رقم 10
NOTE: 1. You do not have to set up the Time and Date manually because the telephone company will automatically update this with the Callers ID information when your phone rings (twice or more). To get back to the standby mode (for dialing), press the DELETE button until the normal display shows. 2. The factorys default setting of the dialing mode is TONE, so you dont need to set it again if you want to use TONE dialing mode. 3. When your phone is set to pulse service, this phone can be switch
ملخص المحتوى في الصفحة رقم 11
MEMORY DIALING You can quickly dial the numbers you stored into the 3 one-touch speed dial buttons or 10 two-touch speed dial memories. Storing Phone Number into Memory 1. Press the STORE button, (short for programming) appears in the display. 2. Dial the phone number you want to store. You can store up to 22 digits, including a TONE ( ) and a PAUSE (REDIAL/ PAUSE), each of which is counted as one digit. 3. For one-touch dialing: For two-touch dialing: Press one of the 3 one- Press t
ملخص المحتوى في الصفحة رقم 12
CALLER ID FEATURES Understanding the Caller ID service Caller ID allows the callers phone number to be shown on the display after the second ring of the call, also in most cases, the callers name, calling time and date. This informations will be stored automatically. In order to enjoy this feature, you must first subscribe to the Caller ID service. To use the call back feature, set the area code (refer to page 7). When You Receive a Call The display as right illustrated will show all the infor
ملخص المحتوى في الصفحة رقم 13
CALLER ID FEATURES Calling back from the Caller ID List A. When Handset is on the Base 1. Display the phone number you want to call back using the UP or DOWN button. 2. Press the CALLBACK/ADJUST button. 3. If the number is only 7-digit (local call), the display will show PICK UP OR ADJ and the phone displayed is 7-digit; if you want the phone number to be 10-digit or 11-digit, press the CALLBACK/ADJUST button once or twice more. 4. If the phone number is 10-digit, the display will show PICK U
ملخص المحتوى في الصفحة رقم 14
CALLER ID FEATURES Deleting the Data from the Caller ID List TO DELETE THE CALLER ID MEMORY ONE BY ONE 1. Display the callers ID you want to delete. 2. Press the DELETE button twice quickly, the display shows the next or previous call, and the data is deleted. TO DELETE ALL THE CALLER ID MEMORIES 1. Make sure that all NEW calls have been reviewed (NEW CALL INDICATOR at the back of the handset does not flash). 2. Press the UP or DOWN button to display any call, make sure the display does not sho
ملخص المحتوى في الصفحة رقم 15
WALL MOUNTING This phone can be mounted on a wall phone plate. If you do not have a modular wall phone plate installed, please consult with your phone company or installer to get one, or see the following for installation without a wall plate. 1. Use the SHORT STRAIGHT WALL CORD, and plug one end into the rear of the phone. 2. Plug the other end into the WALL JACK. 3. Put the phone over the WALL PLATE, make sure both posts fit into slots on the back of the phone. Then slide down to lock the phon
ملخص المحتوى في الصفحة رقم 16
TROUBLE SHOOTING CHECK PROBLEMS Is any plug disconnected from the modular phone plug? Is any jack improperly wired? No dial tone Use another phone to test the jack. Are all cords connected properly? Are all 3 Phone does not AA batteries installed? Make sure they are work installed according to the polarity shown. Phone does not RINGER switch may be set to OFF? Slide ring switch to HI or LOW position. Check the TONE/PULSE setting. You may Can not dial only have PULSE service. Set the TONE/ PULS
ملخص المحتوى في الصفحة رقم 17
TROUBLE SHOOTING (continued) PROBLEMS CHECK Pick up the phone before the second ring, or your phone received no information or unclear information. Static can cause this Shows in the message. If this condition persists, contact display your local telephone company to ensure there is no problem with your phone line. The DELETE button must be quickly pressed twice to erase a single call record. To erase Cannot erase ALL call records, display any record using the all records in UP or DOWN button, t
ملخص المحتوى في الصفحة رقم 18
LIMITED WARRANTY We warrant this product to be free from defects in material and workmanship under normal use for a period of 1 year after purchase, and we will repair it free of charge or replace it at no charge, should it become defective under this warranty, providing you submit proof of purchase (sales slip) with the set. During the initial 1 year period after original purchase, we will service the set that is returned to LENOXX ELECTRONICS CORP., prepaid, at no charge. After the initial 1 y
