ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
CONTENTS DESCRIPTION 3 Introduction 5 Important safety information 5 Connecting the telephone 5 SETTING UP Ringer settings 6 Tone / Pulse switch 7 Time break recall switch 7 VOLUME AND TONE ADJUSTMENT Receiving volume and tone 8 Sending volume level adjustment 9 USING THE PHONE Answering incoming call 10 Making a call 10
ملخص المحتوى في الصفحة رقم 3
DESCRIPTION Flashing incoming ring Direct memory buttons Phonebook insert card Tone reception adjustment Volume reception adjust- ment Extra volume and tone activation Memory storing key Time break recall button Mute button Last number redial 3
ملخص المحتوى في الصفحة رقم 4
DESCRIPTION Ringer level adjustment Sending level switch switch Volume & Tone adjustment ON/OFF Tone / Pulse Line cord switch switch socket* Time break recall switch (*) Classified TNV-3 according to EN60950 standard. Reception Tone Reception volume adjustment adjustment 4
ملخص المحتوى في الصفحة رقم 5
INTRODUCTION IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl,kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shoc
ملخص المحتوى في الصفحة رقم 6
SETTINGS 1 - RINGER SETTINGS A switch located on the upper side allows the ringer to be switched : Off, : Low, : Hi Your phone comes with the ringer switched to «High» and the melody set to «6»: Low Middle High Melody 1 1 2 3 Melody 2 4 5 6 (by default) Melody 3 7 8 9 If you don’t like the ringer
ملخص المحتوى في الصفحة رقم 7
SETTING UP 2 - TONE/PULSE SWITCH (T/P) The Tone/Pulse switch is factory pre-set to Tone position (T). In the US,all telephone exchanges now use Tone dialling.If your phone does not dial out, it is probably being used from an older private switch- board (PBX). In this case,theTone/Pulse switch must be moved to Pulse. 3 - TIME BREAK RECALL SWITCH (600/100) Check the Time Break Recall setting of your Ampli1100. For the US, the Time Break Recall should be set to 600 mS. It can be switched to
ملخص المحتوى في الصفحة رقم 8
VOLUME AND TONE ADJUSTMENT 1- RECEIVING VOLUME AND TONE ADJUSTMENT You can adjust the receiving volume and tone according to your own hear- ing requirements. The button AMPLIFY allows extra volume and tone functions to be activated or deactivated during the conversation. Tone and volume adjustment (15dB to 30dB) is only activated when the switch located at the rear side of your phone is set to ON. When this button is set to OFF only the volume can be adjusted from 0dB to 15dB. When th
ملخص المحتوى في الصفحة رقم 9
VOLUME AND TONE ADJUSTMENT Adjust the TONE and VOLUME buttons to fit the levels to your own hearing requirements. TONE Bass Treble +10dB max +10dB max Normal Volume +20dB max Normal 15dB OFF 0dB 35dB ON 15dB 2 - SENDING VOLUME LEVEL ADJUSTMENT If your voice is quiet or called parties have difficulty hearing you, you can increase the sending level volume with the switch located on the upper side. You can also decrease the sending volume if required.
ملخص المحتوى في الصفحة رقم 10
USING THE TELEPHONE 1 - ANSWERING INCOMING CALLS - When an incoming call is received the phone will ring and the incoming call indicator will flash. To answer the call lift the handset and speak. - On completion of the call, carefully replace the handset in the cradle to release the line. 2 - MAKING A CALL - Lift the handset. - Await the dial tone and dial required number. - On completion of the call, carefully replace the handset in the cradle. 3 - LAST NUMBER REDIAL - Lift the handset. - Awai
ملخص المحتوى في الصفحة رقم 11
USING THE TELEPHONE 6 - STORING TELEPHONE NUMBERS Your telephone Ampli1100 can store 12 direct memories. To store a number please follow instructions below: - Lift the handset. - Press PROG button. - Press M1, M2, ... M12 to locate the number. - Dial the number. - Press PROG again Button. Numbers will be lost after few hours if you disconnect your phone. Entering a new number in the same location will automatically erase the previous number. 7 - DIALING STORED NUMBERS - Lift the handset a
ملخص المحتوى في الصفحة رقم 12
REGULATORY COMPLIANCE - This equipment complies with Part 68 of the FCC rules and the require- ments adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. - All applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided (i.e. RJ11C) in the package with each piece of approved terminal eq
ملخص المحتوى في الصفحة رقم 13
REGULATORY COMPLIANCE NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Some cordless telephones operate at frequencies that may cause interference to nearby TV’s and VCR’s; to minimize or prevent such interference, the base of the cordless telephone should not be placed near or on t
ملخص المحتوى في الصفحة رقم 14
GUARANTEE Sonic Alert warrants the phone against any defect in materials or workman- ship for the period of one year from the date of purchase. Should you experience a problem, contact our customer service department. Be sure to save your sales receipt as proof of purchase date should you need warranty service. Within a period of one year from purchase date, Sonic Alert will repair or replace (our discretion) your phone at no cost, if a defect in materials or workmanship is found. If we elect
