ملخص المحتوى في الصفحة رقم 1
SPOEB10xx-100
User’s Guide
Stand-Alone Media Converter
Power Over Ethernet
10/100Base-TX to 100Base-FX
The SPOEB10xx-1xx Power over Ethernet (POE)
is a two port 10/100Base-TX to 100Base-FX media converter capable of providing
power to Data Terminal Equipment (DTE) Power Devices (PD) via the Media
Dependent Interface (MDI) twisted pair cable. The SPOEB10xx-100 emulates Power
Sourcing Equipment (PSE) and provides power via the 10/100Base-TX interface for a
remote PD device that complies with the I
ملخص المحتوى في الصفحة رقم 2
SPOEB10xx-1xx Part Number Port One - Copper Port Two - Duplex Fiber-Optic Installation 10/100Base-TX 100Base-FX CAUTION: All installation and service must be performed by qualified service Single fiber, Installed in pairs personnel. Read and follow all warning notices and instructions marked on the product and included in this manual. SPOEB1029-100 RJ-45 SC, 1310Tx/1550Rx nm single mode 100 m (328 ft.)* 20 km (12.4 miles) SPOEB1029-101 RJ-45 SC, 1550Tx/1310Rx nm single mode Set the configuration
ملخص المحتوى في الصفحة رقم 3
SPOEB10xx-1xx Installation -- continued Installation -- Continued Eight-position configuration switch -- continued Eight-position configuration switch -- continued 6 6 - PSE Power 2 2 - Speed Up - Enables PSE power. Up - Forces 100 Mb/s on the copper port. Down - Disables PSE power. PSE Enabled Down - Forces 10 Mb/s on the copper port. The IEEE 802.3af™ standard allows a device to TP 100Mb/s Enabled provide power (PSE - Power Sourcing Equipment) (Only when Auto-Negotiation is disabled) to a
ملخص المحتوى في الصفحة رقم 4
SPOEB10xx-1xx Installation- Continued Installation -- Continued Far-End Fault (always enabled) Install the fiber cable -- continued This troubleshooting feature generally used in conjunction with Link Pass � Connect the male TX cable connector to the female RX port. Through to notify both end devices of a link loss. If the fiber RX signal is lost � Connect the male RX cable connector to the female TX port. on the far end converter, the converter will automatically generate a far-end fault signal
ملخص المحتوى في الصفحة رقم 5
SPOEB10xx-1xx Installation -- Continued Operation Power over Ethernet (PoE) Status LEDs The SPOEB10xx-1xx media converter transmits electrical power, along with The SPOEB10xx-100 media converter front panel is shown below. data, to remote devices over standard twisted-pair cable in an Ethernet network. There are two modes of transmitting 48VDC PoE as defined in IEEE 802.3af: PWR TX RX LACT Mode A uses pins 1&2, 3&6 to transmit data and power; Mode B uses pins 4&5, POE 7&8 to transmit power. T
ملخص المحتوى في الصفحة رقم 6
SPOEB10xx-1xx Cable Specifications -- Continued Cable Specifications SPOEB1015-100 (DC-Powered) 1310 nm multimode The cable’s physical characteristics must meet or exceed IEEE 802.3™ Fiber-optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm specifications. Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm Link Budget: 26.0 dB Copper cable Category 5: (Minimum Requirement) SPOEB1016-100 (DC-Powered) 1310 nm multimode Gauge 24 to 22 AWG Fiber-optic Transmitter Power: min: -5.0 dBm
ملخص المحتوى في الصفحة رقم 7
SPOEB10xx-1xx Technical Specifications Troubleshooting For use with Transition Networks Model SPOEB10xx-100 or equivalent If the media converter fails, isolate and correct the fault by determining the answers to the following questions and then take the indicated action: Standards IEEE 802.3, IEEE 802.3af Data Rate 10/100 Mb/s 1. Is the media converter power LED ON? Packet Size (Max) 1522 bytes NO: Mac Address 2K � Is the barrel connector fully inserted into the media converter? � Is the adapte
ملخص المحتوى في الصفحة رقم 8
SPOEB10xx-1xx Troubleshooting -- continued Contact Us Technical Support 5. Is data being passed through the device? Technical support is available 24 hours a day. NO U.S.A. and Canada: 1-800-260-1312 International: 00-1-952-941-7600 � Ensure the Powered Device (PD) IEEE 802.3af compliant. � Ensure the load to the Powered Device (PD) is less than 0.4 Amp. Transition Now � Is a data source connected; if not, connect a data source to the Chat live via the Web with Transition Networks Technical Supp
ملخص المحتوى في الصفحة رقم 9
SPOEB10xx-1xx Compliance Information CISPR22/EN55022 Class A CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instr
