ملخص المحتوى في الصفحة رقم 1
AT-S95 Version 2.0.0.27
AT-8000GS Switch
Software Release Notes
Please read this document before you begin to use the management software.
The following topics are included in this document
“Supported Platforms” on page 1
— “New Features” on page 2
— “Operational Notes” on page 2
— “Resolved Issues” on page 2
— “Known Issues” on page 2
“Upgrade Procedure” on page 4
“Product Documentation” on page 8
“Where to Find Product Information and Management Software Updates” on page 8
“His
ملخص المحتوى في الصفحة رقم 2
AT-S95 Version 2.0.0.27 Software Release Notes The AT-8000GS/24, AT-8000GS/24POE, and AT-8000GS/48 switches can be combined together in a six-unit high stack. What’s New in Version 2.0.0.27 New Features None Operational Notes The default setting of the MODE LED is FDX (instead of ACT) when the switch is first turned on for Version 2.0.0.26 management software. Resolved Issues Fatal error reporting task LPCL, when users perform 802.1x authentication (CQ 134428 ATI293) Guest VLAN timeout
ملخص المحتوى في الصفحة رقم 3
AT-S95 Version 2.0.0.27 Software Release Notes Security (port lock): Port security mechanism is not triggered for MAC violation if MAC is learned on another locked port as a secured MAC address. Mac authentication - MAC auth. fails if the default of the radius server is not md5. Recommended User Work around: Use md5 as default of the radius server. PN 613-001778 Rev A 3 Allied Telesis, Inc.
ملخص المحتوى في الصفحة رقم 4
AT-S95 Version 2.0.0.27 Software Release Notes Upgrade Procedure This section describes how to upgrade the AT-S95 bootloader and software to the latest version using both the CLI and web interfaces. See the following subsections: “Upgrading the AT-S95 Bootloader Code and Software with the CLI” on page 4 “Upgrading the AT-S95 Bootloader and Software with the Web Browser Interface” on page 5 Allied Telesis strongly recommends that you upgrade your switch’s boot loader to the latest version,
ملخص المحتوى في الصفحة رقم 5
AT-S95 Version 2.0.0.27 Software Release Notes 6. Reboot the device with the following command: console# reload This command causes the switch to reboot. By the end of the reboot process, the final code drop will be running. Note To upgrade stacked AT-8000GS switches, see the AT-S95 Management Software CLI User’s Guide for instructions. Upgrading the AT-S95 Bootloader and Software with the Web Browser Interface To upgrade the AT-S95 bootloader and management software to the latest version with
ملخص المحتوى في الصفحة رقم 6
AT-S95 Version 2.0.0.27 Software Release Notes The File System tab is displayed. See Figure 2 on page 6. Figure 2. File System Tab 3. Select the type of TFTP operation to perform. Click both of the following: Download Firmware 4. In the Source File Name field, type the bootloader filename: ati8000gs_boot-2001.rfb 5. From the pull down menu under the Destination File heading, select Bootfile. 6. Enter the IP address of the TFTP server in the TFTP Server IP Address heading. 7. Click Apply. The
ملخص المحتوى في الصفحة رقم 7
AT-S95 Version 2.0.0.27 Software Release Notes 8. Click OK. 9. In the Source File Name field, type the filename of the AT-S95 image: ats95-20027.ros 10. From the pull down menu under the Destination File field, select Software Image. 11. Click Apply. The Copy Finished popup window is displayed. See Figure 3 on page 6. 12. Click OK. 13. Select the System Utilities tab. See Figure 4. Figure 4. System Utilities Tab after Image 2 has been Loaded 14. In the After Reset column, select Image 2 from the
ملخص المحتوى في الصفحة رقم 8
AT-S95 Version 2.0.0.27 Software Release Notes 17. Click the Reset button. The switch is rebooted. Product Documentation For hardware installation instructions for the AT-8000GS switches, refer to the following manual: AT-8000GS Series Stackable Gigabit Ethernet Switches Installation Guide For software management instructions, refer to the following manuals: AT-S95 Management Software CLI User’s Guide AT-S95 Management Software Web Browser Interface User’s Guide These documents are availa
ملخص المحتوى في الصفحة رقم 9
AT-S95 Version 2.0.0.27 Software Release Notes In some cases where more than one switch has the same STP Bridge Priority value in a network, the switch with the higher MAC address would be elected as the STP root bridge. This issue has been resolved. After a switch is operation for a period of time, it may stop forwarding traffic on some ports and does not provide link up/down indications for those ports. This issue has been resolved. SNMP— Added support for SNMP trap when master stack
ملخص المحتوى في الصفحة رقم 10
AT-S95 Version 2.0.0.27 Software Release Notes Contacting Allied Telesis If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/ support. You can find links for the following services on this page: 24/7 Online Support — Enter our interactive support center to search for answers to your product questions in our knowledge database, to check support tickets, to
ملخص المحتوى في الصفحة رقم 11
AT-S95 Version 2.0.0.27 Software Release Notes Contacting Allied Telesis If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/ support. You can find links for the following services on this page: 24/7 Online Support — Enter our interactive support center to search for answers to your product questions in our knowledge database, to check support tickets, to