ملخص المحتوى في الصفحة رقم 1
Pro-Switch/8F
8 Port 100FX
Fast Ethernet Switch
FEP-37008-C (SC)
FEP-37008-T (ST)
908 Canada Court
City of Industry, CA 91748 U.S.A.
Phone: 626.964.7873 or 800.346.6668 Fax: 626.964.7880
www.unicomlink.com e-mail: info@unicomlink.com
USER’S MANUAL
©UNICOM 2001. UNICOM and “A Network Systems Solution” are trademarks of UNICOM Electric, Inc.
All rights reserved. Specifications subject to change without notice.
Rev: 10.03
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Package Contents Package contents include the following: Pro-Switch/8F; 100Base-FX Fast Ethernet Switch Power cord Four (4) adhesive-backed rubber feet Rack-mount brackets User’s manual Warranty card Pro-Switch/8F Power Cord User’s Guide Rubber Feet Rack-mount Brackets with screws IMPORTANT: If any piece is missing or damaged, please contact your local dealer or reseller for service. For Your Records Product Name: Serial Number: Date of Purchase: Purchased from: Notes: 1
ملخص المحتوى في الصفحة رقم 4
Table of Contents Package Contents ……………………………1 Table of Contents ……………………………2 Preface ………………………………………3 Introduction……………………………………4 Key Features …………………………………4 Hardware Description Front Panel ……………………………………5 Ports …………………………………………5 DIP Switch Set-up ……………………………6 LEDs …………………………………………7 Connecting to Power …………………………8 General Installation Selecting a Site for the Switch ……………9 Rackmount Installation ……………………10 Connecting the Power………………………11 Networking Application ……………………12 Specifications ………………
ملخص المحتوى في الصفحة رقم 5
Preface Benefits of Switching Ethernet switching technology has dramatically boosted the total bandwidth of a network. It puts configuration flexibility and bandwidth adaptability into the local workgroups where the majority of work is generated. It further eliminates congestion problems inherent to the CSMA/CD protocol and improves predictable response time under heavy network loads. In the past, expensive routing equipment was used to reduce the congestion under heavy loads. Now, high performa
ملخص المحتوى في الصفحة رقم 6
Introduction Specifications The 8 Port Pro-Switch/8F is a high-speed, professional-grade Fast Standards: 100Base-FX, IEEE 802.3u Ethernet switch that provides wire-speed, a Fast Ethernet switching Ports: 100Base-FX technology that allows high-performance, low-cost connections up to Full- Duplex, 100Mbps Ethernet networks. With the Fiber Optic ports, this is a Speed: 100Base-FX: 200Mbps full-duplex perfect, flexible backbone switch. 100Mbps half-duplex Performance: 148,800pps forwarding rate pe
ملخص المحتوى في الصفحة رقم 7
Network Application Hardware Description This section provides a few samples of network topology in which the This Section describes the hardware of the Pro-Switch/8F and gives a Switch is used. The Pro-Switch/8F is designed to be used as a backbone physical and functional overview of its features. switch. With its large address table (4000 MAC address), Fiber ports, and high performance, it is ideal for connecting WANS to LAN network The Front Panel segments. The front panel consists of (8) fi
ملخص المحتوى في الصفحة رقم 8
DIP-Switch Setup Power On The DIP-switch is used to configure full- or Half-duplex switching. The DIP- Connect the power cord to the power socket on the rear panel of the switch setup is as follows: Switch. The other side of power cord connects to the power outlet. The internal power supply in the Switch works with AC in the voltage range 100- Position Description 240VAC, frequency 50~60Hz. Check the power indicator on the front panel UP: Enables Full-Duplex Operation for 100Based-FX ports (def
ملخص المحتوى في الصفحة رقم 9
LEDs Rackmount Installation Included with the Pro-Switch/8F are brackets allowing the switch to be Per Device: Power mounted in a standard EIA-sized, 19-inch rack. The Switch can be placed Per Port: LNK (Link) in a wiring closet with other equipment. ACT (Activity) FDX (Full Duplex) Perform the following steps to rack mount the switch: A. Align one bracket with the holes on one side of the switch and secure The LED Indicators gives real-time information of systematic operation it with the smal
ملخص المحتوى في الصفحة رقم 10
Connecting to Power General Installation Connect the supplied AC power cord to the receptacle on the back of the switch, This chapter presents step-by-step installation instructions for this eight- and then plug the cord into a standard AC outlet with a voltage range from 100 port Ethernet Switch. to 250 VAC. Selecting a Site for the Switch As with any electronic device, you should place the Switch where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference.
