ملخص المحتوى في الصفحة رقم 1
MIL-S8TA
8-Port 10/100/1000 BASE-T
Unmanaged Switch
User Guide
Rev. A1
2006-09-25
ملخص المحتوى في الصفحة رقم 2
Regulatory Approval - FCC Class A - UL 1950 - CSA C22.2 No. 950 - EN60950 - CE - EN55022 Class A - EN55024 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. European Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage D
ملخص المحتوى في الصفحة رقم 3
FCC STATEMENT This equipment has been tested and found to comply with the limits for a class A device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference on radio communic
ملخص المحتوى في الصفحة رقم 4
Content Introduction................................................................. 1 Features.....................................................................................................1 Package Contents......................................................................................2 Hardware Description................................................. 3 Physical Dimensions ..................................................................................3 Front Panel
ملخص المحتوى في الصفحة رقم 5
Introduction The 8-port 10/100/1000BASE-T Switch with Auto MDI/MDIX is an unmanaged multi-port Switch that can be used to build high-performance switched networks. This switch is a store-and-forward device that offers low latency for high-speed networking. The Switch is designed for the core of the network backbone computing environment to solve traffic block problems at SME (small, medium enterprise) businesses. The 8-port 10/100/1
ملخص المحتوى في الصفحة رقم 6
Package Contents Unpack the contents of the switch and verify them against the checklist below. 8-port Switch Power Cord. User Guide. 8-port Switch Power Cord User manual Package Content Compare the contents of your switch package with the standard checklist above. If any item is missing or damaged, please contact your local dealer for service. 2
ملخص المحتوى في الصفحة رقم 7
Hardware Description Physical Dimensions The physical dimensions of the Switch is 165mm x 100mm x 32.5 mm (L x W x H) Front Panel The front panel of the 8-Port Gigabit switch consists of LED-indicators (100/1000, Link/Activity, Full duplex/Collision) for each Gigabit port and power LED-indicator for unit. RJ-45 Ports (Auto MDI/MDIX): 8 10/100/1000 N-way auto-sensing for 10Base-T, 100Base-TX or 1000Base-T connections. (In
ملخص المحتوى في الصفحة رقم 8
LED Status Description Green Power On Power Off Power is not connected The port is operating at the speed of Green 1000Mbps. The port is operating at the speed of 100/1000 Orange 100Mbps. Off No device attached or in 10Mbps mode Green The port is connecting with the device. LNK/ACT Blinking The port is receiving or transmitting data. Off No device attached. Orange The port is operating in Full-duplex mode. FDX/COL Blinking Packet collision occurred on this port. Off No d
ملخص المحتوى في الصفحة رقم 9
MDI/MDIX function). RJ-45 Ports (Auto MDI/MDIX): 8 port auto-negotiation 10/100/1000 Mbps Ethernet RJ-45 connectors [Auto MDI/MDIX means that you can connect to another Switch or workstation without changing non-crossover or crossover cabling.] 5
ملخص المحتوى في الصفحة رقم 10
Installation This section shows the installation procedures of the switch. Set the Switch on a sufficiently large flat space with a power outlet nearby. The surface where you put your Switch should be clean, smooth, level, and sturdy. Make sure there is enough clearance around the Switch to allow attachment of cables, power cord and air circulation. Attaching Rubber Feet A. Make sure mounting surface on the bottom of the Switch is grease and dust free. B. Remove adhesive ba
ملخص المحتوى في الصفحة رقم 11
Power On Connect the cord of power to the power socket on the rear panel of the Switch. The other side of power cord connects to the power outlet. Check the power indicator on the upper panel to see if power is properly supplied. 7
ملخص المحتوى في الصفحة رقم 12
Technical Specification The following table provides the technical specification of 8-ports Gigabit Switch. IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet Standard IEEE 802.3ab Gigabit Ethernet IEEE 802.3x Flow Control and Back-pressure Protocol CSMA/CD Technology Store-and-Forward switching architecture 14,880 pps for 10Mbps 148,800 pps for 100Mbps Transfer Rate 1,488,000 pps for 1000Mbps Connector RJ-45; Auto-MDIX on all ports MAC Address 8K Mac addr
ملخص المحتوى في الصفحة رقم 13
10BASE-T: 2-pair UTP/STP Cat. 3, 4, 5 cable EIA/TIA-568 100-ohm (100m) 100BASE-TX: 2-pair UTP/STP CAT. 5 cable Network Cable EIA/TIA-568 100-ohm (100m) Gigabit Copper: 4 pair UTP/STP CAT. 5 cable EIA/TIA 568 100-ohm (100M) Per port: 100/1000, Link/Activity, Full duplex/ LED Collision Per unit: Power Power Supply AC 100~240V, 50/60Hz Power 7.6 Watt (maximum) Consumption (DC) Operation 0 to 45 (32 to 113 ) Temperature Operation 1
