ملخص المحتوى في الصفحة رقم 1
105TX-POE & 105FX-POE
Unmanaged Industrial Ethernet
POE Switches
User Manual &
Installation
Guide
Rev. 041008 1
ملخص المحتوى في الصفحة رقم 2
Industrial Power over Ethernet Installation Guide 105TX-POE 105FX-XX-POE 105FXE-XX-YY-POE Where: XX = ST or SC and YY = -15, -40, or -80 Rev. 041008 2
ملخص المحتوى في الصفحة رقم 3
Copyright, © N-TRON Corp., 2008 820 S. University Blvd., Suite 4E Mobile, AL USA 36609 All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-TRON Corp. is prohibited, except as allowed under copyright laws. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks of their respective owners. The information contained in this document
ملخص المحتوى في الصفحة رقم 4
GENERAL SAFETY WARNINGS WARNING: Do not operate the equipment in the presence of flammable gasses or fumes. Operating electrical equipment in such an environment constitutes a definite safety hazard. WARNING: If the equipment is used in the manner not specified by N-TRON Corp., the protection provided by the equipment may be impaired. WARNING: Do not perform any services on the unit unless qualified to do so. Do not substitute unauthorized parts or make unauthorized modific
ملخص المحتوى في الصفحة رقم 5
HAZARDOUS LOCATION INSTALLATION REQUIREMENTS 1. This equipment is suitable for use in Class I, Div 2, Groups A, B, C, and D, or unclassified or non- hazardous locations only. 2. WARNING: Explosion Hazard - Substitution of components may impair suitability for Class I, Division 2. 3. WARNING: Explosion hazard, do not disconnect while the circuit is live or unless the area is known to be non-hazardous. 4. WARNING: Explosion Hazard - Do not remove or replace the device unless
ملخص المحتوى في الصفحة رقم 6
Functional Overview The 105TX-POE and 105FX-POE Power over Ethernet Unmanaged Industrial Ethernet Switches are designed to provide power over Ethernet for POE capable devices where running a power line is either not possible or not cost effective. This feature allows an end user to power a POE camera, wireless access point, or any other POE capable device without the need for running separate wires for power. This also allows the ability for a centralized battery backup for all thes
ملخص المحتوى في الصفحة رقم 7
PACKAGE CONTENTS Please make sure the switch package contains the following items: 1. 105TX-POE or 105FX(E)-POE 2. Instruction Sheet Contact your carrier if any items are damaged. UNPACKING Remove all the equipment from the packaging, and store the packaging in a safe place. File any damage claims with the carrier. CLEANING Clean only with a damp cloth. INSTALLATION Read the following warnings before beginning the installation: WARNING Never install or w
ملخص المحتوى في الصفحة رقم 8
DIN-Rail Mounting Install the unit in a standard DIN rail. Recess the unit to allow at least 2” of horizontal clearance for CAT5e cable bend radius. To install the unit to 35mm industrial DIN rail, To remove the unit from the 35mm industrial place the top edge of the included mounting DIN rail, place a flat head screwdriver into the bracket on the back of the unit against the DIN release clip found at the bottom of the unit, and rail at a 1
ملخص المحتوى في الصفحة رقم 9
FRONT PANEL From Top to Bottom: Power LED POE POE Status LED SPD Speed LED (105TX-POE only) LNK/ACT Link/Activity LED RJ45 Ports Auto sensing 10/100BaseT Connection LED MODE OF OPERATION Note: Redundant power inputs will not balance the power load. Only load from one power supply is used at a time. Rev. 041008 9
ملخص المحتوى في الصفحة رقم 10
APPLYING POWER (Top View) Unscrew & Remove the DC Voltage Input Plug from the top header. Install the DC Power Cables into the Plug (observing polarity on unit). Plug the Voltage Input Plug back into the top header. Tightening torque for the terminal block power plug is 0.22 Nm/0.162 Pound Foot. Turn the power on the wire. Note: It is only safe to turn the power on the wires after the wires have been secured to the switch. WARNING: Inserting the input plug while the 48VDC is a
ملخص المحتوى في الصفحة رقم 11
N-TRON GROUNDING TECHNIQUES FOR 105TX-POE AND 105FX-POE The grounding philosophy of any control system is an integral part of the design. N-Tron switches are designed to be grounded, but the user has been given the flexibility to float the switch when required. The best noise immunity and emissions (i.e. CE) are obtained when the N-Tron switch chassis is connected to earth ground via a drain wire. Some N-Tron switches have metal din-rail brackets that can ground the switch if the di
ملخص المحتوى في الصفحة رقم 12
RJ45 CONNECTOR CRIMP SPECIFICATIONS Please reference the illustration below for your Cat5 cable specifications: Rev. 041008 12
ملخص المحتوى في الصفحة رقم 13
TYPICAL APPLICATIONS STAR TOPOLOGY Rev. 041008 13
ملخص المحتوى في الصفحة رقم 14
RING TOPOLOGY Rev. 041008 14
ملخص المحتوى في الصفحة رقم 15
CONNECTING THE UNIT For the 100BaseFX Fiber Optic port (105FX-POE), remove the dust cap(s) from the fiber optic connector and connect the fiber optic cables. The TX port on the local unit should be connected to the RX port of the far end device, and the RX port should be connected to the TX port of the far end device. For 10Base-T ports, plug a Category 3 (or greater) twisted pair cable into the RJ45 connector. For 100Base-T ports, plug a Category 5 (or greater) twisted pair cable i
ملخص المحتوى في الصفحة رقم 16
FCC STATEMENT This product complies with Part 15 of the FCC-A Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection aga
ملخص المحتوى في الصفحة رقم 17
Regulatory Approvals: Safety: UL Listed per ANSI/ISA-12.12.01-2000 (US and Canada) This apparatus is suitable for use in Class I, Div 2, Groups A, B, C, D, T4 EMI: EN 61000-6-4, EN 55011 - Class A FCC Title 47, Part 15, Subpart B - Class A ICES-003 – Class A EMS: EN6 1000-6-2 IEC 61000-4-2 (ESD) IEC 1000-4-3 (RS) IEC 61000-4-4 (EFT) IEC 61000-4-5 (Surge) IEC 61000-4-6 (Conducted Disturbances) Warranty: 3 years from the date of purchase. Rev. 041008 17
ملخص المحتوى في الصفحة رقم 18
KEY SPECIFICATIONS Physical Height: 3.50” (8.89 cm.) Width: 1.50” (3.81 cm.) Depth Including Din-Rail Clip: 4.22” (10.72 cm) Weight: 0.70 lbs. (0.32 kg) Electrical Input Voltage: 46-49 VDC Input Current: 1.6 A @ 48 VDC (under full load) 65 mA @ 48 VDC (no POE in use, switch in full use) Inrush Current: 26 Amp/1.3 ms @ 48VDC Input Ripple: Less than 100 mV Input Wire Size: 10-20 AWG Environmental Operating Temperature: -40°C to 85°C
ملخص المحتوى في الصفحة رقم 19
N-TRON Limited Warranty N-TRON, Corp. warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use and service, for the applicable warranty period from the date of purchase from N-TRON or its authorized reseller. If a product does not operate as warranted during the applicable warranty period, N-TRON shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to r
