ملخص المحتوى في الصفحة رقم 1
Installation Guide
10BASE-T/100BASE-TX
8-Port Dual-Speed Hub
Model: KF-8D
DOC.980329-KF8D-K
P/N: 750-0109-001
ملخص المحتوى في الصفحة رقم 2
Ó 1998 KTI Networks Inc. All rights reserved. No part of this docu- mentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of KTI Networks Inc. to provide notification of such revi- sion or change. For more information, contact: United
ملخص المحتوى في الصفحة رقم 3
8-Port Dual-Speed Ethernet/Fast Ethernet Hub Installation Guide DOC.980330-KF8D-NK P/N: 750-0109-002
ملخص المحتوى في الصفحة رقم 4
The information contained in this document is subject to change without prior no- tice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment genera
ملخص المحتوى في الصفحة رقم 5
Table of Contents Chapter 1 Introduction Introduction ............................................................................... 1 Features ................................................................................... 2 Dual-speed Hub Technology .................................................... 3 Chapter 2 Installation Unpacking ................................................................................. 4 Checking AC Power......................................................
ملخص المحتوى في الصفحة رقم 6
1. Introduction KF-8D dual-speed Fast Ethernet/Ethernet hub is designed to allow easy and flexible migration from 10Mbps Ethernet to 100Mbps Fast Ethernet. The hub complies with IEEE 802.3 and IEEE 802.3u repeater specifications and supports 10Mbps and 100Mbps con- nectivity over UTP cabling in the same hub. The hub provides 8 dual-speed TP ports. All of the TP ports support auto-sensing function that allows the hub to detect the connection speed auto- matically. The hub also provides complete d
ملخص المحتوى في الصفحة رقم 7
Features • Complies with IEEE 802.3 and IEEE 802.3u standard for Ethernet/Class II Fast Ethernet repeater • Provides a configuration switch (10M/100M/AUTO) to set all 8 TP ports as 10BASE-T ports, 100BASE-TX ports or 10/100 auto-sensing ports. • In AUTO mode, each TP port can support either an Ethernet 10Mbps connection or a Fast Ethernet 100Mbps connection with auto-sensing the connection speed. • The hub provides one uplink jack that allows easy linking of two hubs via straight-through UTP cab
ملخص المحتوى في الصفحة رقم 8
Dual-speed Hub Technology Dual-speed hub is designed to support connections with different speeds in the same hub. It makes a network planning simpler, espe- cially when an environment is containing 10Mbps Ethernet and 100Mbps Fast Ethernet technologies. It also allows a smooth mi- gration from an Ethernet network to a Fast Ethernet network. A dual-speed hub is actually equipped with one 10Mbps repeater and one 100Mbps repeater in one hub unit. Each repeater serves one shared network segment. Th
ملخص المحتوى في الصفحة رقم 9
2. Installation Unpacking Check to see that you have everything before you start the installation. • Installation guide • The hub unit • One AC power adapter for the hub • One wall mount kit Checking AC Power Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for the hub should have the AC voltage matching the commercial power volt- age in your area. The specifications of the AC power adapter are: • AC input power: AC p
ملخص المحتوى في الصفحة رقم 10
The power socket for the AC power adapter is located on the rear of the hub as shown below: Mounting the Hub The hub can be placed on a desktop as a stand-alone unit. It also can be mounted on a wall. The following procedure describes how to mount the hub onto a wallboard or wood (a stud, heavy wooden paneling, etc.) using the wall mount kit supplied in the hub package: 1. Using the slot bracket and two washer-head screws in the wall mount kit, screw the slot bracket onto the bottom of the hub i
ملخص المحتوى في الصفحة رقم 11
3. Place the hub against the wall so that the mount bracket fits into the slot bracket on the back of the hub. 4. Slide the hub down until it hangs on the mount bracket. 6
ملخص المحتوى في الصفحة رقم 12
3. Making Network Connections Network Connectors and Rear Switch The hub provides 8 dual-speed TP ports. Each can support one con- nection to either a 10BASE-T Ethernet device or a 100BASE-TX Fast Ethernet device using 2-pair UTP cable. One configuration switch is located on the rear panel. The switch is used for setting the operation mode for the hub. Three selections are available as follows: AUTO mode Set all TP ports to be auto-sensing ports 100M mode Set all TP ports to be 100BASE-TX ports
ملخص المحتوى في الصفحة رقم 13
RJ-45 Connectors Each of Port #1 to Port #7 provides one RJ-45 connector, which are implemented as MDI-X jack. An MDI-X jack is designed with internal crossover function. The function allows a connection to a computer using straight-through UTP cable. The Port #8 provides one MDI-X RJ-45 connector and one MDI-I RJ-45 connector. Only one connector can be used at the same time. The pin definitions for MDI-X jack and MDI-I jack are as follows: PIN# MDI-X Jack MDI-I Jack 1 Rx+ Tx+ 2 Rx- Tx- 3 Tx+
ملخص المحتوى في الصفحة رقم 14
Connecting to Computers The RJ-45 connectors labeled 1X to 8X can be used for connecting to the network adapter installed in a computer. The network adapter can be a 10BASE-T adapter, a 100BASE-TX adapter, or a 10/100 dual-speed NWay adapter. The following table lists the cables used for connecting to different network adapters: Adapter connected UTP cable used Maximum length 10BASE-T adapter Category 3, 4 or 5 100 meters 100BASE-TX adapter Category 5 100 meters 10/100 NWay adapter Category 5 1
ملخص المحتوى في الصفحة رقم 15
Connecting to Hubs The following table lists the types and the maximum number of hub connections depending on the configuration switch setting: Configuration Types of hubs Connections 10M mode 10BASE-T hubs up to 8 100M mode 100BASE-TX Class II hub one 100M mode Dual-speed Class II hub one AUTO mode 10BASE-T hubs up to 8 AUTO mode 100BASE-TX Class II hub one AUTO mode Dual-speed Class II hub one The cables used and maximum distance allowed for a hub connection are: Hub Port connected Cable used
ملخص المحتوى في الصفحة رقم 16
Connecting to a Fast Ethernet Hub Since the KF-8D is designed to comply with IEEE 802.3u Class II repeater specifications, it can support one connection to another 100BASE-TX Class II hub. The connection rules are: 1. The other hub which is connected to KF-8D must comply with IEEE 802.3u Class II repeater specifications. 2. No more than two hubs can be cascaded in the network. The following figure illustrates the maximum Fast Ethernet network expansion using two KF-8D hubs: 11
ملخص المحتوى في الصفحة رقم 17
4. Interpreting LED Indicators The following figure shows the locations of the LED indicators: Power LED: indicates the status of the repeater power source. State Indication Interpretation On Normal The power of the hub is on. Off Problem No power is being supplied to the hub. Collision LED: indicates the collision detected by the hub. The LED is normally off and it blinks when there are collisions on 10M shared segment or 100M shared segment. Link/Rx 1-8 LED: indicates the link status and rece
