ملخص المحتوى في الصفحة رقم 1
User’s Manual
IR REMOTE
MIN.
UNITY
MAX.
INPUT 3
SCP 100P
SCP 100P
Control Panel
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan
1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Road, #04-01 Daisan DMJ Building 6F
Anaheim, CA 92805 3821 AH Amersfoort PM Industrial Building 3-9-1 Kudan Minami
68-390-01
USA The Netherlands Singapore 368363 Chiyoda-ku, Tokyo 102-0074 Japan
714.491.1500 +31.33.453.4040 +65.6383.4400 +81.3.3511.7655
Pri
ملخص المحتوى في الصفحة رقم 2
Precautions Safety Instructions • English Warning Extron’s Warranty Power sources This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. The third (grounding) pin is in the literature provided with the equipment. Extron Electronics warrants this product agains
ملخص المحتوى في الصفحة رقم 3
Table of Contents Chapter 1 • Introduction and Installation ................... 1-1 About the SCP 100P .............................................................. 1-2 Installation Instructions .................................................... 1-2 Preparing the site, installing the wall box ........................... 1-2 Rear panel (circuit board) and cabling................................. 1-4 Pre-installation testing/troubleshooting.............................. 1-4 Mounting the SCP to
ملخص المحتوى في الصفحة رقم 4
Table of Contents, cont’d SCP 100P Chapter One 1 Introduction and Installation About the SCP 100P Installation Instructions SCP 100P Table of Contents ii
ملخص المحتوى في الصفحة رقم 5
Intr Introduction and Installation, cont’d oduction and Installation 4. Insert the wall box (if used) into the wall, and attach About the SCP 100P the wall box to the wall stud (2” x 4”) or furniture The Extron SCP 100P control panel replicates the front panel with nails or screws, leaving the front edge flush with controls of the Extron System 5cr Plus system switcher, and it is the wall surface, as shown in the following also compatible with the System 5cr switcher. The Input 3 illustration.
ملخص المحتوى في الصفحة رقم 6
Introduction and Installation, cont’d SCP 100P, and watching the LEDs on the switcher to see if the Rear panel (circuit board) and cabling system switches to the desired inputs. The connections between the SCP 100P and the System 5cr Plus can be tested even if input/output devices are not available. 1 Mounting the SCP to the wall box Once the system has been cabled and tested, the control pad can be installed in the wall or furniture. 1. With power removed, insert the SCP 100P into the wall or f
ملخص المحتوى في الصفحة رقم 7
Introduction and Installation, cont’d Application diagram SCP 100P Below is an example of a typical installation of an SCP 100P control pad and a System 5cr Plus switcher. SYSTEM 5 Plus AUDIO PC1 INPUT IR DISPLAY AUDIO COMPUTER ROOM POWER MUTE MODE PC1 PC2 INPUT 3 VID1 VID2 PC MAX. TX RX LEARN VID VID VID CLIP CONFIG Y/C Y/C Y/C MIN. VOLUME RETRY Front IR 40 Remote LIGHTING ROOM POWER MUTE MODE VOLUME MAX. CLIP MIN. PC1 PC2 INPUT 3 VID1 VID2 SHADES/DRAPES Optional IR Broadcaster Room Control SCP
ملخص المحتوى في الصفحة رقم 8
Operation, cont’d Operation The SCP 100P replicates the front panel controls of the Display Power button and LED — Once the System 5cr Plus has System 5cr Plus. been programmed with the commands for the specific projector, pressing this button toggles the projector’s power The System 5cr Plus cannot be configured from the on or off. SCP 100P control pad. All switcher setup must be done The LED lights when projector power is on. The LED from the switcher’s front panel or via RS-232 control. bl
ملخص المحتوى في الصفحة رقم 9
Operation, cont’d Volume control knob — Rotate this knob to adjust the audio 5 SCP 100P volume (audio gain) for the amplified output. The volume control knob can be used as a master volume control for both audio outputs if all the audio inputs have the same level. There is no physical limit to this knob’s rotation. The Min or Max LED will light briefly when the knob has reached its functional minimum or maximum limit. Audio gain/attenuation can be set per input via the switcher’s front panel
ملخص المحتوى في الصفحة رقم 10
Specifications, Parts, Accessories, Dimensions, cont’d Specifications, Parts, Accessories, Dimensions Specifications Accessories These recommended items are available from Extron: Control/remote — control pad IR controller module ......... IR 401 (optional) Cable/accessory Part number General Comm-Link cable (50’) 29-461-01 Power ................................... 12VDC, at 60 mA, from the System 5cr Plus switcher Comm-Link cable (100’) 29-461-02 Temperature/humidity .... Storage -40° to +158°F
ملخص المحتوى في الصفحة رقم 11
Specifications, Parts, Accessories, Dimensions, cont’d Template Use the template as a guide to mark and cut the hole in the wall or furniture through which the SCP 100P will be installed. The template includes the recommended 0.1” (0.25 cm) clearance on all sides of the electrical wall box to allow room for the raised areas surrounding the knockouts. See chapter two for details on installing the SCP 100P. The light gray area represents the layout of the electrical box (3.75"H x 3.75"W) agains
