ملخص المحتوى في الصفحة رقم 1
™
7C03 MMAC SmartSWITCH
Installation Guide
9031699-01
ملخص المحتوى في الصفحة رقم 2
Notice NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. In no event shall Cabletron Systems be liable for any incidental, indirect, special, or consequential damages whatso
ملخص المحتوى في الصفحة رقم 3
Notice FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
ملخص المحتوى في الصفحة رقم 4
Notice VCCI NOTICE This equipment is in the 1st Class Category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference (VCCI) by Information Technology Equipment aimed at preventing radio interference in commercial and/or industrial areas. Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be caused to radios and TV receivers, etc. Read
ملخص المحتوى في الصفحة رقم 5
Notice DECLARATION OF CONFORMITY Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer’s Name: Cabletron Systems, Inc. Manufacturer’s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03886-5005 European Representative Name: Mr. J. Solari European Representative Address: Cabletron Systems Limited Nexus House, Newbury Business Park London Road, Newbury Berkshire RG13 2PZ, England Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC E
ملخص المحتوى في الصفحة رقم 6
CONTENTS CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL .........................................................................1-1 1.2 USING THE SMARTSWITCH MANUAL SET ...................................1-1 1.3 7C03 MMAC SMARTSWITCH OVERVIEW .......................................1-2 1.3.1 7X00 SmartSwitch Controller Module........................................1-4 1.3.2 SmartSwitch interface modules ...................................................1-4 1.3.3 Operations........
ملخص المحتوى في الصفحة رقم 7
CHAPTER 1 INTRODUCTION Welcome to Cabletron Systems 7C03 MMAC SmartSwitch Installation Guide. This manual is a simple installation and reference guide. The 7C03 MMAC SmartSwitch is a unique self-contained 1 module that can be placed into an MMAC series chassis . 1.1 USING THIS MANUAL Chapter 1, Introduction, discusses the features of the 7C03 MMAC SmartSwitch. Chapter 2, Installation, explains the process of inserting the 7C03 MMAC SmartSwitch in an MMAC chassis
ملخص المحتوى في الصفحة رقم 8
Introduction In addition, any local management information that is specific to a particular SmartSwitch interface module is described in a module specific local management appendix. For example, the 7E03-24 Ethernet SmartSwitch Interface Module Local Management Appendix explains information that is specific to local management of the 7E03-24 Module only. 1.3 7C03 MMAC SMARTSWITCH OVERVIEW The 7C03 MMAC SmartSwitch (Figure 1-1) is a metal enclosure that can be placed into two modu
ملخص المحتوى في الصفحة رقم 9
Introduction 7X00 7F00 7E03-24 SP SP SP SN PWR CPU 24 SN A MAC ADR F 10 D SN B D P A A S B I S 1 E T B 13 P A SB 12 A 10 F B D A A P D S B S I E 2 T B 1 Figure 1-1. 7C03 MMAC SmartSwitch Because the 7C03 MMAC SmartSwitch does not attach to the data channels on the backplane of an MMAC chassis, data can not be transmitted internally from SmartSwitch interface modules to the other modules in the MMAC chassis. However, data can be transmitted externally from SmartSwitch interface modul
ملخص المحتوى في الصفحة رقم 10
Introduction 1.3.1 7X00 SmartSwitch Controller Module The 7X00 SmartSwitch Controller Module is the only processing and management element in the 7C03 MMAC SmartSwitch. The 7X00 Module has no front panel data ports. All data enters and exits the 7X00 Module via the SmartSwitch Bus on the 7C03 MMAC SmartSwitch’s backplane. The 7X00 Module directs incoming data to its intended destination by using a group of Application Specific Integrated Circuits (ASICs) collectively known as
ملخص المحتوى في الصفحة رقم 11
Introduction 1.3.3 Operations Data packets entering through the front panel of a SmartSwitch interface module in the 7C03 MMAC SmartSwitch are converted by the module’s hardware into frames that have a common “canonical” format. Canonical frames are forwarded along the 7C03’s SmartSwitch Bus to the 7X00 Module in slot one. The configuration of the 7X00 Module (either traditional switch or SecureFast Packet Switch) determines the manner in which canonical frames are processed. When ope
ملخص المحتوى في الصفحة رقم 12
Introduction 1.4 RELATED MANUALS The following manuals supplement the procedures and other technical data provided in this manual. The procedures will be referenced where appropriate, but will not be repeated. Cabletron Systems SmartSwitch Interface Module User’s Guides (module specific). Cabletron Systems SmartSwitch Interface Module Local Management Appendices (module specific). Cabletron Systems 7X00 SmartSwitch Controller Module User’s Guide 1.5 GETTING HELP If you need additio
ملخص المحتوى في الصفحة رقم 13
CHAPTER 2 INSTALLATION This chapter contains instructions for unpacking and installing the 7C03 MMAC SmartSwitch in an MMAC chassis. The 7C03 MMAC SmartSwitch can be installed in an MMAC-M5FNB or in an MMAC-M8FNB chassis. Note: Because of the modular nature of the power supplies and interface modules in the MMAC-M5FNB and MMAC-M8FNB chassis, there is no one standard MMAC configuration that can be used as a reference. The way you configure your MMAC-M5FNB or MMAC-M8FNB chassis (n
ملخص المحتوى في الصفحة رقم 14
Installation 2.2 INSTALLING THE 7C03 MMAC SMARTSWITCH Prior to installing the 7C03 MMAC SmartSwitch, please read the note that appears on page 2-1. To install the 7C03 MMAC SmartSwitch in an MMAC-M5FNB or MMAC-M8FNB chassis, use the following steps and refer to Figure 2-1. 1. Remove the blank panels covering the slots in which the 7C03 MMAC SmartSwitch will be installed. All other unused slots must remain covered to ensure proper air flow and cooling. 2. Hold the 7C03 MMAC SmartSwitc
ملخص المحتوى في الصفحة رقم 15
Installation card guide plastic rail Figure 2-1. Installing the 7C03 MMAC SmartSwitch in an MMAC-M8FNB 2-3
ملخص المحتوى في الصفحة رقم 16
CHAPTER 3 TECHNICAL SPECIFICATIONS This chapter includes the technical specifications for Cabletron Systems 7C03 MMAC SmartSwitch. Cabletron Systems reserves the right to change these specifications at any time without notice. 3.1 SERVICE MTBF: >200,000 hours MTTR: <0.5 hour 3.2 PHYSICAL 3.2.1 Dimensions 33.1D x 29.2 H x 10 W centimeters (12.8 D x 9.0 H x 3.9 W inches) 3.2.2 Weight Unit: <9.0 kgs. (<20 lbs.) Shipping: <9.0 kgs. (<20 lbs.) 3.3 ENVIRONMENTAL Oper
