ملخص المحتوى في الصفحة رقم 1
Operation/Reference Guide
AVS-SL-PR-0401-0601
Solecis Presentation Switcher
4x1 RGBHV, 6x1 SVID, 10x1 Stereo, CP
Last Updated: 10/23/2008
Solecis Switchers
ملخص المحتوى في الصفحة رقم 2
AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity. AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase, with the following exceptions: � Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the
ملخص المحتوى في الصفحة رقم 3
Safety Instructions Safety Instructions Overview Please read these instructions before using your Procon switcher. Failure to comply with these instructions could result in fire, electrical shock, personal injury, death, or damage to the equipment. Power Source Use only a three-wire grounding type source. The power source should not exceed 264VAC. Do not remove under any circumstances the ground wire. Power Cord Use only the cord shipped with the unit. Do not use the cord if it has become dama
ملخص المحتوى في الصفحة رقم 4
Safety Instructions AVS-SL-PR-0401-0601
ملخص المحتوى في الصفحة رقم 5
Table of Contents Table of Contents Safety Instructions .............................................................................................. a Overview .................................................................................................................. a Power Source............................................................................................................ a Power Cord........................................................................................
ملخص المحتوى في الصفحة رقم 6
Table of Contents Mute ON ........................................................................................................................ 8 Mute OFF ....................................................................................................................... 8 Front Panel Disable ........................................................................................................ 8 Front Panel Enable ..........................................................................
ملخص المحتوى في الصفحة رقم 7
Overview Overview The Solecis AVS-SL-PR-0401-0601 Presentation Switcher (FG1330-2011-01) combines switching of PC, computer, video and audio for presentation and conference rooms, home cinema, AV Rental Companies and any environment where a number of mixed source types need to be displayed. The AVS-SL-PR-0401-0601 features a total of ten inputs and a programmable serial output for controlling projectors, plasma displays and other display devices. FIG. 1 Solecis AVS-SL-PR-0401-0601 Presenta
ملخص المحتوى في الصفحة رقم 8
Overview AVS-SL-PR-0401-0601 Specifications (Cont.) Sync Output Level: TTL Impedance: 75 ohm Video Video Inputs: 6 YC or Composite Connector: Phono/RCA/Cinch 4Pin Din S-Video Level: Analogue Max Input: 1V P-P Impedance: 75 Ohm Bandwidth: 50MHz -3dB Return Loss: -30dB@1MHz, -22dB@5MHz Differential Phase Error: 0.05% Differential Gain Error: 0.03% Input Crosstalk: -60dB@1MHz Video Output: 1-YC, 2-Composite Connector: Phono/RCA/Cinch 4Pin Din S-Video Level: Analogue Gain: Unity Audio Audio Inputs:
ملخص المحتوى في الصفحة رقم 9
Connections Connections Typical Installation For Use With a Projector Connect the RGB, Video and Audio sources to the Input sockets on the rear panel of the unit. The RGB/Video inputs are 75 ohm terminated and the audio inputs 47Kohm terminated. The RGB/Video and audio outputs are fully 75 ohm and 600 ohm driven respectively for connection to long cable runs. It is imperative that the input sources are fully compatible with the display and sound devices. Video Connections There are 4 PC in
ملخص المحتوى في الصفحة رقم 10
Connections 4 AVS-SL-PR-0401-0601
ملخص المحتوى في الصفحة رقم 11
Operation Operation Front Panel Source Selection To select a Source press the Button corresponding to the numbered Input. The button will illuminate. A PC input will be routed to the PC output sockets. A selected Video Input will also be routed to its respective Composite or S-Video output. If a PC input is selected then the last selected video input will remain on its respective output and vice versa. The Audio Channel will switch to the highlighted Input. (Unless the Unit is controlled by R
ملخص المحتوى في الصفحة رقم 12
Operation Input mode only When the 2011 is powered up a mode command will be sent to a display on the first press of any Input select button. The command will either be RGB, Composite or S-Video depending on the button pressed. This will ensure a display device is set to the correct mode to display the input selected. Each time a different source type is selected then a mode command will be sent to the display device. For this function to work the Display must be ON Power On/Off mode When the
ملخص المحتوى في الصفحة رقم 13
SET Commands SET Commands Input Switching The following command switches input sources. Byte 1 Byte 2 Byte 3 Byte 4 Byte 5(optional) (Header) (Address) (Video Input) (Audio Input) RGB Delay (see note) E8 00 to FF 00 to 0A 0 to OA 01 to FF The Audio Inputs can be switched independently from the Video. Bytes 3 and 4 01 to 04 correspond to PC inputs 1 to 4 05 to 0A correspond to video inputs 1 to 6 00 for Blank 1F no change Byte 5 This switches the input sync but holds the RGB in blank for th
ملخص المحتوى في الصفحة رقم 14
SET Commands Attenuation (Changes Level on selected Input only) The Volume level increases 0.5db each time the following command is sent: Byte 1 Byte 2 Byte 3 (Header) (Address) (Increase) E8 00 to FF 0D The Volume level decreases 0.5db each time the following command is sent: Byte 1 Byte 2 Byte 3 (Header) (Address) (Decrease) E8 00 to FF 0E Absolute Attenuation Level An attenuation value can be set directly using the following command: Byte 1 Byte 2 Byte 3 Byte 4 (Header) (Address) (Volume
ملخص المحتوى في الصفحة رقم 15
GET Commands GET Commands Switch and Volume Status Feedback Transmit Byte 1 Byte 2 Byte 3 (Header) (Address) EF 00 to FF 80 Receive Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 (Header) (Address) C8 00 to FF PC or Video Input Audio input Input volume level 0= Blank 1 to 4 = PC I/P 5 to 0A= Vid I/P The same string will be transmitted each time an input is selected. Request Address Transmit Byte 1 Byte 2 Byte 3 (Header) (Address) 38 62 DA Receive Byte 1 Byte 2 (Header) (Address) C8 00 to FF Request Atte
ملخص المحتوى في الصفحة رقم 16
GET Commands Identity Command Sending this command: Byte 1 Byte 2 Byte 3 Byte 4 F2 09 EA 80 The unit will return: Byte 1 Byte 2 6E 04 =2010 10 AVS-SL-PR-0401-0601
ملخص المحتوى في الصفحة رقم 17
Device Manager Device Manager Overview This software can be used for configuring the 2011 to control external display devices. It is downloadable from our website www.procon.co.uk under support. Connection Connect the serial port of the PC as follows: PC (D9) 2011 Pin 5 gnd Pin 2 tx Pin 3 rx Run Device Manager. If the connection is correct the software will automatically detect the 2011. Click on the 2011 and a virtual panel will appear (FIG. 2): FIG. 2 Device Manager - Virtual Panel Operatio
ملخص المحتوى في الصفحة رقم 18
Device Manager FIG. 4 Device Manager - Adding a Device to the Library The manufacturer's data sheet will be required. If the string needs to be transmitted more than once then select the number of times from the count drop-down list and set a suitable interval period. If the power on/off function is to be enabled then set a warm up/cool down time and click on Set/Enable. Finally click on Program Device to download the information. For operation see section on Display device serial output. 12
ملخص المحتوى في الصفحة رقم 19
Device Manager 13 AVS-SL-PR-0401-0601
ملخص المحتوى في الصفحة رقم 20
It’s Your World - Take Control™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 � 469.624.8000 � 469-624-7153 fax � 800.932.6993 technical support � www.amx.com © 10/08 2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time.
