ملخص المحتوى في الصفحة رقم 1
SAMSON
HS300.4 / HS500.4 / HS800.4
HS1500.1D / HS2500.1D
ملخص المحتوى في الصفحة رقم 2
SAMSON HIGH PERFORMANCE AMPLIFIERS The Samson Series products have been designed to a very high level of performance, with features unavailable in any other product. All of the amplifiers have variable crossovers built in, with added touches such as subsonic filter, bass equalization and a remote Level control module(some models) that allows subwoofer Level control from the drivers seat. To ensure years of listening pleasure, all amplifiers have a built in diagnostic mode that will detect sho
ملخص المحتوى في الصفحة رقم 3
WIRE GAUGE GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion. Lower power amplifiers w
ملخص المحتوى في الصفحة رقم 4
AMPLIFIER FEATURE DESCRIPTIONS SAMSON AMPLIFIERS: - Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation - CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU except the mono amps which are capable of 4, 2 and 1-Ohm loads. WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE - The input sensitivities for rated output powers are variable from 0.2 volts to 6 volts. WARRANTY PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel a
ملخص المحتوى في الصفحة رقم 5
HS300.4 / HS500.4 / HS800.4 4-CHANNEL AMPLIFIER APPLICATIONS 4 CHANNEL FULL RANGE SYSTEM Here we show how to use the 4 channel amplifiers as straight forward discrete 4 - HI PASS: N/A channel full range units. - LOW PASS: N/A Interconnect cable checklist: Channels 3/4: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables. - HI PASS: N/A - LOW PASS: N/A Switch setting checklist: - 1/2CH X-OVER: FULL Level control checklist: - 3/4CH X-OVER: FULL - Refer to the sectio
ملخص المحتوى في الصفحة رقم 6
HS300.4 / HS500.4 / HS800.4 4-CHANNEL AMPLIFIER APPLICATIONS Front/Rear high pass, using a mono amplifier for mono sub bass The combination of a 1 and a 4 channel amplifier, utilizing their built in crossovers, makes it a snap to put together a full system with front and rear Channels 3/4: highs, with mono sub bass. - HI PASS: 100 Hz - LOW PASS: N/A Interconnect cable checklist: - Using good quality RCA cables, feed the front and rear outputs of a head unit to 2 channel bass amplifier: the inpu
ملخص المحتوى في الصفحة رقم 7
HS1500.1D / HS2500.1D MONO AMPLIFIER APPLICATION Basic application Interconnect cable checklist: Crossover frequency control checklist: Connect the inputs to a suitable source, e.g. a head unit with good quality RCA cables. LOW PASS: 40Hz to 150Hz Connect the LINE OUT to the inputs of the system highs amplifier. SUBSONIC:15 Hz to 55 Hz BASS EQ: 0 to +12dB Use at least #12 gauge speaker wiring. The amps have dual speaker terminals, simplifying the hookup of multiple speakers. These amps are mon
ملخص المحتوى في الصفحة رقم 8
6
ملخص المحتوى في الصفحة رقم 9
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE HS300.4 / HS500.4 / HS800.4 General: At this point you are ready to get more specific on the settings for your amplifier. HPF (High Pass): -When in HPF operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the HPF to 100Hz, the amplifier will
ملخص المحتوى في الصفحة رقم 10
TROUBLESHOOTING A SYSTEM The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the PROTECT system built into all Hifonics amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A sort circuit on the loudspeaker le
ملخص المحتوى في الصفحة رقم 11
Maxxsonics Limited Warranty As the manufacturer of Maxxsonics, MB Quart, Autotek, Crunch and Hifonics car audio products, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one (1) Year from date of purchase. All other parts and accessories of the system are warrantied to be free from defects in material and workmanship for one (1) year from date of purchase. Maxxsonics will repair or replace at it’s option and f
ملخص المحتوى في الصفحة رقم 12
OEM Integration Accessories MX-1 Premium High To Low Level Converter MX-3 Bass Controller * Converts High Level OEM speaker wires to Ultra Clean RCA Low Level Outputs * High Level Inputs: Accepts all types of High level Inputs * Parametric Bass EQ: Provides a wide array of subwoofer output signal including floating ground and high voltages up to 30 volts. shaping controls to enhance bass response and sound quality including * Audio Signal Sense / Hardwire Turn-On: Audio sense detec
ملخص المحتوى في الصفحة رقم 13
PART#: A710
