Dual ALB10 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

ALB10
INSTALLATION/OWNER'S MANUAL
10"  Ported  Enclosure  with  Built-in  Amplifier

ملخص المحتوى في الصفحة رقم 2

PREPARATION Getting  Started Thank you for purchasing the Dual ALB10 10" ported enclosure with built-in amplifier. Although Dual has attempted to ensure the information in this manual is accurate, please be aware that any part of it is subject to change without notice. Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your Dual ALB10 is installed by a professional installer or an authorized dealer. Before  You  Start  •

ملخص المحتوى في الصفحة رقم 3

INSTALLATION Safety  First CAUTION ! The  following  instructions  are  designed  to  ensure  safety  during  installation  and  use  of  the  ALB10.  Failure  to  heed  these  instructions  can  result  in  injury  or  damage  to the unit or vehicle. The following installation instructions are intended to be used as a basic guideline. If you feel unsure about installing this speaker system yourself, Dual recommendsacquiringtheservicesofaprofessionalcaraudioinstallation center. Befor

ملخص المحتوى في الصفحة رقم 4

INSTALLATION Connection  Descriptions Note:  Be  sure  to  follow  specific  instructions  included  with  your  amplifier  installation  kit  (not  included  with  this  amplifier).  The  information  below  should  be  used  a  general  guideline  only. Power  Wire  (+12V) • Disconnect   negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • Plan   wire routing before cutting any wires to length. Begin by routin

ملخص المحتوى في الصفحة رقم 5

INSTALLATION Connections and Controls 1 2 3 4 5 6 7 8 9 10 11 1 Hi-LevelInputs 7 Power Indicator 2 LineIn(Left) 8 GroundConnection 3 LineIn(Right) 9 RemoteConnection 4 CrossoverFrequency 10 PowerConnection 5 InputLevelControl 11 Fuse(15A) 6 PhaseControl 5

ملخص المحتوى في الصفحة رقم 6

INSTALLATION Typical  Wire  Routing 18” MAXIMUM BATTERY HIGH LEVEL INPUT (SPEAKER WIRE) High  Level  Input  (Speaker  Wire) High  level  inputs  should  only  be  used  when  RCA  outputs  are  not  available  from  the  head  unit. Connect the head Grey = Right (+) Grey/Black = Right (-) unit speaker outputs to the high level input connector Black = Ground as shown below. The black wire (signal reference White/Black = Left (-) ground) may or may not require a connect

ملخص المحتوى في الصفحة رقم 7

INSTALLATION Control  Setup  and  Adjustment Low level (RCA) input signal is preferred for best Input  Signal  Connections performance. Typical trunk-mount installations Low  Level  (RCA) require a 17-20 foot RCA cable. Most trucks and behind-seat applications require a 6-12 foot RCA cable. Using twisted pair construction RCA cables will minimize noise. The adjustable crossover is used to filter out Crossover  Frequency  frequencies above 40Hz ~ 160Hz

ملخص المحتوى في الصفحة رقم 8

INSTALLATION Troubleshooting Problem Cause Action Unit  will  not  turn  on BAT+ wire not connected or incorrect voltage Check connections for proper voltage (no  power  LED  indicator) REM wire not connected or incorrect voltage (11~16VDC) GND wire not connected Check connection to ground Fuse(s) blown Replace fuse(s) Unit  has  power  -  LED  is  Volume turned all the way down Increase volume level at head unit green  (but  no  sound) Speaker defective or damaged

ملخص المحتوى في الصفحة رقم 9

WARRANTY Limited  One-Year  Warranty This warranty gives you specific legal What  to  do? rights. You may also have other rights 1. Before you call for service, check the which vary  from state to state. troubleshooting guide in your owner’s manual. A slight adjustment of any Dual Electronics Corp. warrants this custom controls may save you a service product to the original purchaser to be free call. from defects in material and workmanship for a p

ملخص المحتوى في الصفحة رقم 10

INSTALLATION Notes Please keep your original sales receipt and be prepared to For  Your  Records provide this receipt in the event you require service, as your original receipt is considered the best proof of purchase and indicates the date you purchased your Dual product. Dealer Name Dealer Phone Purchase Date Register your product online atwww.dualav.com Register  Your  Product 10

ملخص المحتوى في الصفحة رقم 11

INSTALLATION Specifications Maximum  Output  Power 300 watts Continuous  Output  Power 100 watts Frequency  Response 20-200Hz S/N  Ratio  @  1  watt 85dB Input  Impedance Low level (RCA): 10k ohms Input  Sensitivity  (RCA)  50mV – 3V Crossover  Frequency 40–160Hz Crossover  Slope 6dB/octave Phase 0–180 degrees Fuse 15 amp ATO Dimensions 12.6" x 16.5" x 9.8"  (HxWxD) Design and specifications subject to change without notice. 11

ملخص المحتوى في الصفحة رقم 12

Dual Electronics Corp. Toll Free: 1-866-382-5476 Monday-Friday, 9AM-5PM EST www.dualav.com ©2013 Dual Electronics Corp. All rights reserved. NSA0513-V01 Printed in China