ملخص المحتوى في الصفحة رقم 1
XPE1700
XPE2700
XPE4700
XPE SERIES
INSTALLATION/OWNER’S MANUAL
Mobile Power Amplifiers
ملخص المحتوى في الصفحة رقم 2
XPE SERIES INSTALLATION Preparation Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your DUAL amplifier is installed by a professional installer or an authorized dealer. Before You Start • Disconnect negative battery terminal. (consult a qualified technician for instructions) • Avoid installing the amplifier where it would be subject to high temperatures, such as from direct sunlight, o
ملخص المحتوى في الصفحة رقم 3
XPE SERIES INSTALLATION Connection Descriptions NOTE Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used a general guideline only. Power Wire (+12V) • Disconnect negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • Plan wire routing before cutting any wires to length. Begin b
ملخص المحتوى في الصفحة رقم 4
XPE SERIES INSTALLATION Audio Inputs and Controls X - O V E R R I G H T S U B B A S S S O N I C B O O S T P H A S E 0 FF O N L P O F F 0 FF 6 d B 1 2 d B0 1 8 0 L I N E I N P U T S M I N M A X 5 0 H z 5 0 0 H z X P E 1 7 0 0 G A I N F R E Q U E N C Y L E F T 1 2 3 4 5 6 7 S P E A K E R X - O V E R I N P U T S R I G H T B A S S B O O S T G A I N F R E Q U E N C Y L P O FF H P 0 FF 6 d B 1 2 d B L I N E I N P U T S M I N M A X 5 0 H z 5 0 0 H z X P E 2 7 0 0 L E F T 1 8 2 5 4 6 F R O N T I N
ملخص المحتوى في الصفحة رقم 5
XPE SERIES INSTALLATION Power and Speaker Connections P O W E R S P E A K E R F U S E S + - G ND R E M B A T + 3 0 A 3 0 A X P E 1 7 0 0 1 2 3 4 5 S P E A K E R S P O W E R B R I D G E F U S E + G ND R E M B A T - L E F T + - R I G H T + 2 5 A X P E 2 7 0 0 1 2 3 4 5 S P E A K E R S P O W E R B R I D G E F U S E S - L E F T + - R I G H T + G ND R E M B A T + 2 5 A 2 5 A F R O N T R E A R X P E 4 7 0 0 1 2 3 4 5 Ground Connection Fuse(s) 1 4 Remote Connection Speaker Connection(s) 2 5 +12V
ملخص المحتوى في الصفحة رقم 6
XPE SERIES INSTALLATION Typical Wire Routing REM (TURN-ON LEAD) Main Power Connections Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the +12V lead within 18" of the battery for protection of the vehicle’s electrical system. Fuse Rating Power/Ground Wire Size When replacing fuses, make sure new fuse For optimum performance, use only the wire is the correct type and amperage. Using an size listed below or la
ملخص المحتوى في الصفحة رقم 7
XPE SERIES INSTALLATION Amplifier Connections Subwoofer (mono) Speaker Connections 2 Speakers (stereo) Connect speaker wires observing polarity. The minimum impedance load for the XPE2700 and XPE4700 is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage. The XPE2700 and XPE4700 can be wired for stereo, bridged or stereo/bridged simultaneous operation. Typical Bridged Wiring Typical Stereo
ملخص المحتوى في الصفحة رقم 8
XPE SERIES OPERATION Configuration/Setup Input level Control The input level control (gain) is used to obtain the best possible match between the head unit audio output and the amplifier input. Begin by turning the input level control fully counterclockwise. Next, turn up the head unit volume control around 3/4 of the way up. Adjust the input level control clockwise until audible distortion is heard, then slightly counterclockwise t
ملخص المحتوى في الصفحة رقم 9
XPE SERIES WARRANTY Limited One-Year Warranty This warranty gives you specific legal What to do? rights. You may also have other rights 1. Before you call for service, check the which vary from state to state. troubleshooting guide in your owner’s manual. A slight adjustment of any Dual Electronics Corp. warrants this custom controls may save you a service product to the original purchaser to be free call. from defects in material a
ملخص المحتوى في الصفحة رقم 10
XPE SERIES OPERATION Specifications CEA-2006 Power Standard Specifications (reference: 14.4VDC, 20Hz~20kHz) XPE1700 Power Output (14.4VDC, 20Hz ~ 20kHz): 240 Watts RMS x 1 channel @ 4 ohms and ≤ 1% THD+N 400 Watts RMS x 1 channel @ 2 ohms and ≤ 1% THD+N Total dynamic power: 1000 Watts Signal to noise ratio: 75dBA (reference: 1 watt into 4 ohms) Frequency response: 20Hz ~ 20kHz (-3dB) Amplifier dimensions: 8.95”(L) x 13.3
ملخص المحتوى في الصفحة رقم 11
XPE SERIES OPERATION Notes 11
ملخص المحتوى في الصفحة رقم 12
XPE SERIES OPERATION Troubleshooting Problem Cause Action Unit will not turn on +12V wire not connected or incorrect voltage Check connections for proper voltage (no power LED indicator) REM wire not connected or incorrect voltage (11~16VDC) GND wire not connected Check connection to ground Fuse(s) blown Replace fuse(s) Unit has power - LED is Speaker wires not connected Check connections at speakers blue (but no sound) Volume turned all the
