ملخص المحتوى في الصفحة رقم 1
Heavy duty storage rack
Model 97563
asseMbly, operating, and Maintenance
instructions
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by Harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
save
ملخص المحتوى في الصفحة رقم 2
save tHis Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. iMportant saFety instructions in this manual, on the labeling, and all other information provided with this product: this is
ملخص المحتوى في الصفحة رقم 3
4. Do not overload or exceed the maximum shelf capacity of 600 lb. 5. Do not stand on, or use this Storage Unit as a ladder. 6. Should there be a need to change the level of a shelf, be sure to disassemble and reassemble one shelf at a time following procedures in “Assembly” section located on pages 5 and 6 of this manual. 7. Do not use this Storage Unit for other than intended use. 8. Maintain labels and nameplates on the appliance. These carry important safety information. If unreadable
ملخص المحتوى في الصفحة رقم 4
speciFications Upright Posts: Stamped and Formed 16 Gauge Steel - Q’ty 4 Side Sway Bars: Tubular Steel Construction Materials L - Shaped Safety Pins and Other Hardware: Zinc Plated Steel Shelves: Stamped and Formed Steel Maximum Weight per 600 lb Shelf Shelving Section 22-1/2” L X 13-7/8” W X 1-1/16” H - Q’ty 15 Dimensions unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number show
ملخص المحتوى في الصفحة رقم 5
one on each side, and six Nuts (5). Hand tighten the Nuts (5) initially (see Fig- ures 1 and 2). Flat Washer Nut Bolt Upright Post Safety Pin Long Rod note: Figure 2 Foot Plate at base of uprights Short Rod must rest on the floor. 3. Repeat step 1 to assemble the second Upright Post set. 4. Using two persons, stand up the two Upright Post assemblies in position and at- tach one Cross Beam (6) into the second Slot from the bottom of the two
ملخص المحتوى في الصفحة رقم 6
Upright Post (2) Safety Pin (9) Cross Beam (6) Figure 3 8. Insert the Safety Pins (9) into Holes located in, and lined up with, both the Up- right Posts (2) and Cross Beams (6). This is an important step and will keep the Cross Beams from slipping up and coming loose (See Figure 3). 9. Lay the Steel Shelves (7) as needed into the Cross Beams (6). You can use up to 15 Steel Shelves (7), three per level, or leave some out in order to make room for taller items being stored. 10. Mak
ملخص المحتوى في الصفحة رقم 7
Maintenance and servicing Any maintenance or service not specifically explained in this manual must be performed by a qualified service technician. cleaning and Maintenance 1. periodically inspect the general condition of this Storage Rack. Check for loose screws, misalignment of parts, cracked or broken parts, and any other condition that may affect its safe operation. 2. Wipe down with clean, moist cloth periodically. please read tHe FolloWing careFully THE MANUFACTURER AND/OR DISTRIBUTOR
ملخص المحتوى في الصفحة رقم 8
asseMbly diagraM SKU 97563 For technical questions, please call 1-800-444-3353. Page 8
