ملخص المحتوى في الصفحة رقم 1
ADDENDUM
Addendum No. C3409M
Date December 22, 2005
Manuals Affected C2462M-B, C2403M-C, C2410M-H,
C2491M-B, C2496M
Manual Update Switch Settings for Varifocal Lens
Manual Update The high resolution camera with vari-
focal lens and auto iris is configured at
the factory for automatic exposure.
SWITCH SETTINGS FOR VARIFOCAL LENS
The high resolution camera with varifocal lens and auto iris is configured at the factory for
automatic exposure.
1 AWB Automatic white balance
FACTORY SETTINGS
2 GA
ملخص المحتوى في الصفحة رقم 2
Installation ® 150 Series Camclosure Integrated Camera System C2410M-H (10/05) Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com USA and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
ملخص المحتوى في الصفحة رقم 3
CONTENTS Section Page IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................ 3 REGULATORY NOTICES ............................................................................................................................... 3 DESCRIPTION .............................................................................................................................................. 4 INSTALLATION ......................
ملخص المحتوى في الصفحة رقم 4
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (in- cluding amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8. Use only with the cart, stand, tripod, bracke
ملخص المحتوى في الصفحة رقم 5
FCC, Class B (color, NTSC and PAL cameras - except auto iris models) RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may c
ملخص المحتوى في الصفحة رقم 6
Mounting to 4S Deep Electrical Box 1. Attach adapter plate to the 4S box with the two 8-32 x .750-inch 4S DEEP ELECTRICAL screws. BOX 2. Connect the video cable. WALL OR CEILING 8.32 X .750 SCREW 3. Connect the power wires. (SUPPLIED) ADAPTER PLATE • For 12 VDC, connect the 24 VAC/12 VDC (red) and GND BACK BOX (black) wires to input power. 01063 8.32 X .375 SCREW (SUPPLIED) • For 24 VAC, connect the 24 VAC/12 VDC (red) and 24 VAC (blue) wires to input power. 4. Attach the back box to the adapter
ملخص المحتوى في الصفحة رقم 7
VIDEO 2. 12 VDC Operation Only - The camera CONNECTOR is set for 24 VAC operation at the HEATER factory. For 12 VDC operation re- CONNECTOR move the jumper from the 24 VAC position 24 VAC JUMPER and install it on the 12 VDC JUMPER 12 VDC position. 01065 3. If the heater is installed, plug the heater connector from the camera into the mating connector inside the base. Plug the video connector from the camera into the mating connector inside the base. Turn on power to the camera and monitor. VIDEO
ملخص المحتوى في الصفحة رقم 8
3 Install Dome and Trim Ring Place the trim ring and dome over the back box. If the dome has a liner, position the viewing window over the lens of the camera. Tighten the tamper-resistant screws with the supplied 1/8-inch hollow screwdriver bit. Note 01074 that the screws are installed at an angle. ADJUSTMENTS (COLOR CAMERA ONLY) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however, adjustments may be necessary. 1. Remove the dome and
ملخص المحتوى في الصفحة رقم 9
Auto Iris Level Adjustment If you have a varifocal lens or fixed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness. VARIFOCAL LENS VERTICAL PHASE ADUSTMENT Focus Adjustment for Fixed Focal Length Lens with Auto Iris CAUTION Heater elements could be hot! When camera power is on, use caution when adjusting the camera. To adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screw on the bottom of the l
ملخص المحتوى في الصفحة رقم 10
Switch Settings for Fixed Focal Length Lens with Auto Iris Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions where there are no bright spots that darken other picture details. Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots. ALC/ELC switch: Always ALC FACTORY SE
ملخص المحتوى في الصفحة رقم 11
Switch Settings for Varifocal Lens The high resolution camera with 1 AWB Automatic white balance FACTORY SETTINGS varifocal lens and auto iris is 2 GAM Gamma function configured at the factory for 12345678 3 AGC Automatic gain control optimal performance in lighting 4 ESC Electronic shutter control conditions where auto iris is 5 BLC Backlight compensation required. It is also configured with 6 FL Flickerless OFF the shutter speed set at 1/60 7 AE Automatic exposure = SWITCH POSITION (NTSC) or 1
ملخص المحتوى في الصفحة رقم 12
SPECIFICATIONS General Operating Temperature: -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Pan/Tilt Adjustment: Manual; 360° pan; 180° tilt Construction: Aluminum with steel camera mounting bracket and polycarbonate dome Finish: White polyester powder coat trim ring with charcoal gray back box Dimensions Above Ceiling: 1.75 (H) x 3.50 (W) inches (4.45 x 8.89 cm) Below Ceiling: 2.42 (H) x 5.48 (W) inches (6.15 x 13.90 cm) Bubble: 3.75-inch diameter Environment: Low temperature, indoor/out
ملخص المحتوى في الصفحة رقم 13
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. ® • Three years on Genex Series products (multiplexers, server, and keyboard). ® • Three years on Camclosure and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X
