ملخص المحتوى في الصفحة رقم 1
AUDIO VIDEO SURROUND RECEIVER
VR-804
KRF-V4080D
KRF-V5580D
INSTRUCTION MANUAL
KENWOOD CORPORATION
This instruction manual is for some models. Model availability and features
(functions) may differ depending on the country and sales area.
About the supplied remote control
Compared to standard remote controls, the remote control supplied with this model has several operation
modes. These modes enable the remote control to control other audio/video components. In order to
effectively use the remot
ملخص المحتوى في الصفحة رقم 2
Caution : Read this page carefully to ensure safe Before applying the power operation. Units are designed for operation as follows. How to use this manual U.S.A. and Canada ........................................... AC 120 V only This manual is divided into four sections, Preparations, Operations, Remote Control, and Additional Information. Australia ........................................................... AC 240 V only Europe and U.K. ............................................... AC 230 V
ملخص المحتوى في الصفحة رقم 3
Before applying the power Contents Unpacking Unpack the unit carefully and make sure that all accessories are present. Caution : Read the pages marked carefully to ensure safe operation. FM indoor antenna (1) AM loop antenna (1) For KRF-V4080D For VR-804 Before applying the power ...................................................... 2 and KRF-V5580D Safety precautions ..................................................................... 2 How to use this
ملخص المحتوى في الصفحة رقم 4
Before applying the power Preparing the remote control Channel space switching (Except for the U.S.A., Canada and Australia) Loading the batteries The space between radio channels has been set to the one that prevails in the area to which the system is shipped. However, if the 1 Remove the cover. 2 Insert the batteries. current channel space setting does not match the setting in the area where the system is to be used, for instance when you move from area 1 or area 2 shown in the following table
ملخص المحتوى في الصفحة رقم 5
Before applying the power Special features For the U.S.A. FCC WARNING True home theater sound This equipment may generate or use radio frequency energy. Changes This model incorporates a wide variety of surround modes to bring you or modifications to this equipment may cause harmful interference maximum enjoyment from your video software. Select a surround mode unless the modifications are expressly approved in the instruction according to your equipment or the software you are going to play and
ملخص المحتوى في الصفحة رقم 6
Names and functions of parts Main Unit Frequency display, AUTO DETECT Input display, Preset channel display, indicator Surround mode display DTS indicator 6CH INPUT indicator Speaker indicator MUTE indicator Band indicators DIGITAL indicator AUTO indicator CLIP indicator AB MEMO. indicator ST. indicator TONE indicator TUNED indicator DOLBY DIGITAL DSP indicator Speaker selection indicators indicator LOUDNESS indicator Input channel indicators STEREO indicator PRO LOGIC 96kHzfs indicator Output
ملخص المحتوى في الصفحة رقم 7
Names and functions of parts Remote control unit (RC-R0626) (VR-804/KRF-V5580D) and (RC-R0625) (KRF-V4080D) POWER 1 23 DVD 45 6 POWER 78 9 RECEIVER 0+10 DOWN-PAGE-UP PTY LOUDNESS TOP MENU MENU OSD RETURN SETUP SOUND LISTEN MODE P.CALL P.CALL MULTI CONTROL BAND ENTER TUNING A/B+100 AUTO BASS BOOST DISC SKIP DVD DVD/6CH AUX CD/DVD TUNER MD/TAPE (For RC-R0625 only) DVD DISC SEL. VIDEO1 VIDEO2 ACTIVE EQ TONE If the name of a function is different on this model and on the remote control, the name of
ملخص المحتوى في الصفحة رقم 8
Setting up the system Make connections as shown in the following pages. Input mode settings When connecting the related system components, be sure to refer to the instruction manuals supplied with CD/DVD, VIDEO2 and DVD (VR-804/KRF-V5580D only) or DVD/ the components you are connecting. 6CH (KRF-V4080D only) inputs each include jacks for digital audio input and analog audio input. Do not connect the power cord to a wall outlet until all After completing connections and turning on this model, fol
ملخص المحتوى في الصفحة رقم 9
Setting up the system Connecting audio components Shape of AC outlets U.S.A. and Canada Australia SYSTEM CONTROL jacks % + + To AC wall outlet - - AUDIO L R REC OUT PLAY IN REC OUT PLAY IN AUX CD/DVD MD / TAPE VIDEO1 IN OUT Video component ) IN OUT Cassette deck or MD recorder OUT CD or DVD player Other component OUT EN 9 9 04.1.22, 9:11 PM
ملخص المحتوى في الصفحة رقم 10
Setting up the system Connecting video components + + - - AUDIO VIDEO For VR-804/ DVD KRF-V5580D IN only MONITOR OUT VIDEO 2 IN REC OUT PLAY IN PLAY IN DVD VIDEO 1 VIDEO 2 VIDEO 1 VIDEO 1 IN OUT VIDEO IN Monitor TV Video inputs (Yellow RCA pin cords) Video deck IN IN OUT OUT Video inputs and Audio inputs outputs and outputs (Yellow RCA pin cords) DVD player or LD player Audio OUT Video OUT DVD player or LD player Audio OUT Video OUT A video component with digital audio outputs should be connect
ملخص المحتوى في الصفحة رقم 11
Setting up the system Digital connections The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD) format digital signals. If you have connected any digital components to this model, be sure to read the “Input mode settings” section carefully. 8 + + - - COAXIAL OPTICAL VIDEO 2 CD / DVD DVD DIGITAL IN OPTICAL DIGITAL OUT (AUDIO) Optical fiber cable CD or DVD player COAXIAL DIGITAL OUT (AUDIO) Component wi
ملخص المحتوى في الصفحة رقم 12
Setting up the system Connecting a DVD player (6-channel input) (For KRF-V4080D only) If you have connected a DVD player to this model with digital connection, be sure to read the “Input mode settings” section carefully. 8 + + - - DVD / 6CH INPUT COAXIAL OPTICAL VIDEO CENTER VIDEO 2 CD / DVD DVD IN MONITOR OUT VIDEO 2 IN SUB FRONT SURROUND DVD/6CH WOOFER DIGITAL IN VIDEO 1 VIDEO 1 IN OUT VIDEO OUT FRONT SURROUND SUBWOOFER (Yellow RCA OUT L/R OUT L/R OUT pin cord) DVD player CENTER OUT COAXIAL D
ملخص المحتوى في الصفحة رقم 13
Setting up the system Connecting the speakers Front Speakers Right Left Center Speaker SURROUND FRONT CENTER + + - - R L GRAY BLUE R L C SPEAKERS (8-16Ω ) RED WHITE GREEN SPEAKERS (8 VR-804/KRF-V4080D + + - - KRF-V5580D SURROUND SUB WOOFER SUB WOOFER + PRE OUT VR-804/KRF-V4080D - R L SW GRAY BLUE PURPLE SPEAKERS (8-16Ω ) Powered Subwoofer Right Left Subwoofer Surround Speakers (Be sure to connect both surround speakers) To make sure that each speaker has been connected properly, pay attention to
ملخص المحتوى في الصفحة رقم 14
Setting up the system Connecting the terminals Connecting the antennas AM loop antenna 1 Strip coating. 2 Push the lever. The supplied loop antenna is for use indoors. Place it as far as possible from this model, TV set, speaker cords and power cord, and adjust the direction for best reception. AM antenna terminal connections 3 Insert the cord. 4 Return the lever. 1 Push lever. 2 Insert cord. 3 Release lever. • Never short circuit the + and – speaker cords. FM indoor antenna • If the left and ri
ملخص المحتوى في الصفحة رقم 15
Setting up the system Connecting the system control Connecting system control cords after connecting a KENWOOD SYSTEM CONTROL OPERATIONS audio component system lets you take advantage of convenient system control operations. Remote Control Lets you operate this unit with the system remote supplied with the This unit is compatible only with the [SL-16] mode. The system this model. control operation is not available if the unit is connected in the [XS8], [XS], or [XR] connection mode. Automatic Op
ملخص المحتوى في الصفحة رقم 16
Preparing for surround sound Speaker settings 1 FULL RANGE : For selected KENWOOD speaker – for To enable you to obtain optimum enjoyment from this model’s listening modes, make sure to complete the speaker settings (Subwoofer, Front, example, KS-207HT, KS-207EX, KS-208HT. Center, and Surround speakers) as described below. 2 2WAY 2SPKR : For selected KENWOOD speaker – for example, KS-307HT, KS-308HT, KS-308EX. POWER ON/STANDBY 3 2WAY 3SPKR : For selected KENWOOD speaker – for (KRF-V4080D/ V5580D
ملخص المحتوى في الصفحة رقم 17
Preparing for surround sound 0 Use the MULTI CONTROL knob or keys to select the appropriate 3 Press the SETUP key. Surround speaker setting. • The test tone is turned off. This model enters the mode for inputting the distance to the speakers. If you have selected “LRG” as the Center speaker setting, 1 SURR NML (normal) : Average size Surround speakers are 4 For MANUAL selection, press the SETUP key each time to connected to this model. select the speaker channel. 2 SURR LRG (large) : Large Surro
ملخص المحتوى في الصفحة رقم 18
Normal playback Preparing for playback Listening to a source component Some preparatory steps are needed before starting playback. VOLUME CONTROL POWER ON/STANDBY SPEAKERS (KRF-V4080D/ V5580D) ON/STANDBY INPUT SELECTOR ON/OFF (VR-804) POWER INPUT SELECTOR AUTO ON/OFF (KRF-V4080D/ V5580D) Input Turning on this model Selector 1 Turn on the power to the related components. VOLUME 2 Turn on the power to this model by pressing POWER ON/ STANDBY (for VR-804) or POWER ON/OFF and ON/ STANDBY (for KRF
ملخص المحتوى في الصفحة رقم 19
Normal playback Adjusting the sound Adjusting the LOUDNESS mode (remote control only) You can adjust the Loudness function which controls the low volume SPEAKERS ON/OFF VOLUME CONTROL settings to maintain the music’s richness. The adjustment can be made ACTIVE EQ when this model is in the PCM stereo and analog stereo mode. Press the LOUDNESS key to turn the LOUDNESS setting ON. To cancel Press the LOUDNESS key again so that the “LOUDNESS” indicator goes off. MULTI CONTROL PHONES MUTE Muting the
ملخص المحتوى في الصفحة رقم 20
Recording Recording audio (analog sources) 3 Press and hold the DIMMER key for more than 2 seconds to select the A-REC or M-REC mode during digital input. 1 Rec mode off : The digital input record mode is switched off. 2 A-REC mode : The digital input signals (DTS, Dolby Digital, or PCM) are identified automatically and converted into stereo signals that are ready for recording. 3 M-REC mode : The input signal type at the moment this mode is selected is held throughout this mode. INPUT SELECTOR
