ملخص المحتوى في الصفحة رقم 1
User Manual
XENYX
502/802/1002/1202
Premium 5/8/10/12-Input
2-Bus Mixer with XENYX Mic
Preamp and British EQ
Thank you Table of Contents
Congratulations! In purchasing our XENYX 502/802/1002/1202 Thank you ..................................................................... 1
you have acquired a mixing console whose small size belies its Important Safety Instructions ................................... 2
incredible versatility and audio performance. 1. Introduction ........................
ملخص المحتوى في الصفحة رقم 2
ENGLISH XENYX 502/802/1002/1202 User Manual XENYX 502/802/1002/1202 User Manual 2 3 • Mix: Setting the volume level, frequency distribution Important Safety Instructions 1. Introduction and positioning of the individual signals in the stereo field, level control of the total mix to match the recording XENYX Mic Preamps [6]� Clean only with dry cloth. EN devices/crossover/power amplifier(s). All other mixer [7]� Do not block any ventilation openings. Install in accordance The microphone ch
ملخص المحتوى في الصفحة رقم 3
ENGLISH XENYX 502/802/1002/1202 User Manual XENYX 502/802/1002/1202 User Manual 4 5 ◊ Please note that all units must be properly grounded. MIC LOW CUT 2.2 Stereo channels For your own safety, you should never remove any Each mono input channel offers a balanced microphone input In addition, the mono channels (1002 and 1202) are ground connectors from electrical devices or power 2.2.1 Stereo line inputs via the XLR connector and also features switchable equipped with a steep LOW CUT filter
ملخص المحتوى في الصفحة رقم 4
ENGLISH XENYX 502/802/1002/1202 User Manual XENYX 502/802/1002/1202 User Manual 6 7 FX FX SEND 2.3.3 CD/Tape connectors signal to the monitor(s) or headphones. This will avoid the tape signal being routed to the CD/TAPE OUTPUT. The FX sends of the stereo channels function similar to those of The FX SEND output (does not apply for 502) should be CD/TAPE INPUT the mono channels. However, since the FX send buses are both connected to the input of an external effects unit. The FX TO CTRL ROOM Th
ملخص المحتوى في الصفحة رقم 5
ENGLISH XENYX 502/802/1002/1202 User Manual XENYX 502/802/1002/1202 User Manual 8 9 Strain relief clamp strain relief clamp 3. Installation 4. Specifications Sleeve sleeve ring Mono inputs 3.1 Mains connection Tip tip Microphone inputs (XENYX Mic preamp) AC POWER IN Type XLR connector, electronically Connect the power supply to the 3-pin mains connector balanced, discrete input circuit on the rear of the console. Use the AC adapter supplied to 1 Mic E.I.N. (20 Hz - 20 kHz) connect the c
ملخص المحتوى في الصفحة رقم 6
ENGLISH XENYX 502/802/1002/1202 User Manual XENYX 502/802/1002/1202 User Manual 10 11 sE nd / rEturn 1202 Limited Warranty Power consumption 20 W Aux sends § 1 Warranty [2] This limited warranty does not cover the product if it has been electronically or EN Type ¼" TS jack, unbalanced USA/Canada mechanically modifi ed in any way. If the product needs to be modifi ed or adapted in [1]� This limited warranty is valid only if you purchased the product from a BEHRINGER Impedance approx. 120 Ω Ad
ملخص المحتوى في الصفحة رقم 7
ENGLISH XENYX 502/802/1002/1202 User Manual XENYX 502/802/1002/1202 User Manual 12 13 FEDERAL COMMUNICATIONS Legal Disclaimer § 6 Claim for damage Technical specifi cations and appearance are subject to change without COMMISSION COMPLIANCE notice. The information contained herein is correct at the time of printing. Subject only to the operation of mandatory applicable local laws, BEHRINGER shall BEHRINGER accepts no liability for any loss which may be suff ered by any INFORMATION have no l
ملخص المحتوى في الصفحة رقم 8
ENGLISH This manual is available in English, German, French, Spanish, Italian, Russian, Polish, Dutch, Finnish, Swedish, Danish, Portuguese, Greek, Japanese and Chinese. There may also be more current versions of this document. Download them by going to the appropriate product page at: www.behringer.com
